620389
1
Zoom out
Zoom in
Previous page
1/2
Next page
Siemens Building Technologies CB1B3064en 23.08.2010 1 / 2
Operating Instructions RDF510.2
RDF510.2 the temperature controller that allows you to set the ideal room temperature you want. The controller provides
normal operation with comfort mode and protection mode.
The fan operates either in automatic mode or at the selected speed when using manual mode. You can either rely on the
factory settings or make adjustments that suit your individual needs.
Are your rooms too warm or too cold?
+ /
Only applicable in normal operation (Comfort mode ).
Pressing + or allows you to increase or decrease the current room temperature setpoint
for normal operation (Comfort mode ) in increments of 0.5 °C. The maximum setting
range is from 5...40 °C, unless it is limited by parameters P05 and P06.
Do you want to set your controller to protection mode?
Press the operating mode button several times until the indicator
stop right beside the
Protection mode symbol .
In protection mode , the controller can maintain the lower setpoint of heating for frost
protection according to parameter P03 or the higher setpoint of cooling for moldy resistance
according to parameter P04.
Important:
If the setpoint of protection is set to OFF, the controller will not be activated in protection
mode.
Risk of frost!
Do you want to change the fan mode?
Press the fan mode button until you have selected the desired fan mode.
In automatic mode, the fan speed is automatically selected by the controller and depends
on the setpoint and the actual room temperature. When the room temperature has reached
the setpoint, the fan either remains in fan speed low (factory setting) or switches off
(parameter P21).
In manual mode the fan operates independently and always runs at the same speed:
Low, medium or high.
The actual fan speed is indicated by:
Low Medium High
Do you want to change from heating to cooling mode?
or
When pressing the Heat/Cool mode selector continuously (without intermit tent stop), the
controller changes from heating to cooling or vice versa.
If the controller is commissioned cooling only or heating only, no changeover is possible
(please see parameter P22: factory setting manual H/C changeover).
Recalibrating the sensor
If the room temperature displayed by the controller does not agree with the temperature effectively
measured, the temperature sensor can be recalibrated. For that purpose parameter P07 must be changed.
Proceed as described under Changing the control parameters and follow steps 1 through
3 to select parameter P07.
With step 4, the room temperature displayed can now be matched to the temperature
effectively measured. Each push of the + or button changes the temperature by + or -0.5
°C up to a maximum of + or -3 °C.
With step 7, the recalibration is automatically stored after pressing the + and
simultaneously at End.
Measured room temperature, setpoints
and parameters; °C or °F
Room temperature
Fan mode button
- changing the fan mode
(Auto / manual)
- changing the fan speed
(Low / Medium / High)
H
eat
/C
ool mo
de selector
Cooling mode
Heating mode
Operating mode button
Comfort mode
Protection mode
Button lock/unlock
Colder / Warmer
Changing the room temperature setpoint
Button lock active
Fan Speed
Low Medium High
Automatic fan active
Heat/Cool Mode:
Cooling mode
Heating mode
Operating Mode:
Comfort mode
Protection mode
Indicator for selecting mode
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens RDF510.2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens RDF510.2 in the language / languages: English as an attachment in your email.

The manual is 0,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens RDF510.2

Siemens RDF510.2 Installation Guide - All languages - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info