555877
1
Zoom out
Zoom in
Previous page
1/2
Next page
CE1B3031en / 12.06.2001 Subject to alteration Siemens Building Technologies / Landis & Staefa Division
Operating instructions
Landis & Staefa RDD10…
RDD10... - the temperature controller that allows you to set the ideal room temperature at the time you want.
There are two operating modes available. You can either rely on the factory settings or make settings that suit
your personal needs.
Display
Operation and settings
Normal operation
Display operating mode
changeover-duration
Temporary changeover activated
Energy saving mode
Heating on
Display room temperature
Replace batteries
(only with battery-powered versions)
Warmer / colder
Setting the
temperature setpoints
Operating mode
changeover-duration
Setting and
displaying
Changing the operating mode
between normal operation
and energy saving mode
Room temperature or
operating mode
changeover-duration
Batteries
(only with battery-powered versions)
3031Z11E
1.5V
'AAA'
1.5V
'AAA'
+-
Commissioning
The controller is supplied with factory-set temperatures and operating mode changeover-duration (= 00.0 h). To commission
it, proceed as follows:
Remove the black transit tabs from the two batteries. Check to see if the battery holder is in its correct position. The
controller switches itself on (only with battery-powered types).
Do you require continuous normal operation
or energy saving mode?
By pressing , you switch from normal
operation to energy saving mode, or vice versa.
Then, the setpoint of the selected operating mode
will be continuously maintained.
In normal operation, the display shows
,in
energy saving mode,
.
Are your rooms too warm / too cold?
+
-
By pressing these buttons, you increase or
decrease the room temperature setpoint in
increments of 0.5 °C. Proceed as follows:
Press
to select the operating mode
the setpoint of which you want to change
Press
+
or
-
once
The setpoint display starts flashing
Press these buttons again to change the
temperature setpoint in the range 5 ... 35 °C
5 seconds after the last push, the new
temperature setpoint will automatically be saved.
The display stops flashing and shows the room
temperature currently measured.
Note:
The setpoint in energy saving mode can be set to
0 °C. This means OFF or, in other words, the
controller is not active in energy saving mode and
symbol
will not appear on the display.
Risk of frost!
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens RDD10 - Landis Staefa at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens RDD10 - Landis Staefa in the language / languages: English as an attachment in your email.

The manual is 0,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens RDD10 - Landis Staefa

Siemens RDD10 - Landis Staefa User Manual - German - 2 pages

Siemens RDD10 - Landis Staefa User Manual - Dutch - 2 pages

Siemens RDD10 - Landis Staefa User Manual - French - 2 pages

Siemens RDD10 - Landis Staefa Installation Guide - All languages - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info