555875
7
Zoom out
Zoom in
Previous page
1/8
Next page
CE1G2224X 2015-03-20 7/8
Puesta en marcha
1. Banda de aislamiento de las pilas
Para aislar las pilas, hasta el momento de la puesta en
servicio del controlador, éstas llevan una banda aislante, al
retirar la banda, la unidad empieza a funcionar.
2. Separar la base del controlador
Abrir la tapa y acoplar el reloj como muestra la fig A, (en el
caso de que no esté ya incorporado). Ahora cerrar la tapa
y separar la base del controlador, ver las figuras B y C.
3. Fijar la base en la pared y realizar el
conexionado eléctrico
Ver la fig. D y el apartado “Esquema de conexionado” .
4. Offset
10
15
20
25
30
5
(°C) (°C) Pos.
22.00 20.00 8
21.75 20.00 7
21.50 20.00 6
21.25 20.00 5
21.00 20.00 4
20.75 20.00 3
20.50 20.00 2
20.25 20.00 1
20.00 20.00 0
19.75 20.00 F
19.50 20.00 E
19.25 20.00 D
19.00 20.00 C
18.75 20.00 B
18.50 20.00 A
18.25 20.00 9
5. Adaptación del controlador a la
instalación con los interruptores DIP
5.1 Ciclo de conmutación
Self learning Control autoadaptado (estándar):
Válido para la mayoría de los casos.
PID 12 Para sistemas de control normal:
Instalaciones con variaciones de
temperatura normales.
PID 6 Para sistemas de control rápido:
Instalaciones con grandes variaciones
de temperatura.
2-Pt Para sistemas de difícil control:
Control todo/nada con un diferencial
de conmutación de 0.5 °C (±0.25 °C).
5.2 Activación de los interruptores DIP
Si se cambia la posición de alguno de los dos interruptores
DIP, ¡hay que presionar el pulsador “Reset”, situado
debajo de ellos ! ¡Si no, seguirán activas las anteriores!.
6 Acoplar el controlador sobre su base
Proceder como se muestra en las figuras. E y F.
7 Cambio del reloj de 24 horas por otro
semanal / Sustitución del reloj
Si se precisa el cambio del reloj de 24 horas (AUZ3.1) por
otro semanal (AUZ3.7) o bien si se necesita sustituirlo,
abrir la tapa y proceder como se muestra en la fig. A.
8 Verificación de funciones
a) Abrir la tapa frontal y situar el selector de modos de
funcionamiento en la posición
.
b) Girar el botón superior hasta los 30 °C.
c) El relé del controlador debe actuar en menos de 1
minuto. Si no es así:
· Comprobar que la unidad de control esté bien
acoplada en su base
· Para realizar esta prueba la temperatura ambiente
debe ser menor de 30 °C
d) Girar de nuevo el botón superior hasta la temperatura
normal
, p. ej. 20 °C.
e) Situar el selector de modos de funcionamiento en la
posición AUTO .
9 Notas
· Si el radiador o los radiadores del lugar en el que se ha
instalado el controlador, está equipado con válvula
termostática, ésta debe dejarse totalmente abierta.
· Se deben respetar las normas oficiales que rigen para
instalaciones eléctricas.
· Los dos interruptores DIP se entregan en la posición
OFF, (lado contrario a la marca “ON”)
· Los reajustes posteriores de los interruptores DIP se
activan presionando el pulsador blanco “Reset”.
· Se requiere en todos los casos una protección externa
preliminar con un protector de circuito max. C 10 A.
DE
EN
FR
IT
NL
ES
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens RAV11 - Landis Staefa at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens RAV11 - Landis Staefa in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens RAV11 - Landis Staefa

Siemens RAV11 - Landis Staefa User Manual - English - 2 pages

Siemens RAV11 - Landis Staefa User Manual - German - 2 pages

Siemens RAV11 - Landis Staefa User Manual - Dutch - 2 pages

Siemens RAV11 - Landis Staefa User Manual - French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info