649339
1
Zoom out
Zoom in
Previous page
1/4
Next page
Siemens Building Technologies 4 319 2486 0 f M1761xx 07.02.2008 1/4
4 319 2486 0
M1761
A B C
1761Z11
QAM21xx.200 : 4 x
QAM21xx.600 : 6 x
1761Z14
1761Z13
1761Z03
Montageort
Als Zulufttemperaturfühler oder Begrenzungsfühler
nach dem Ventilator, falls dieser nach dem letzten
Luftbehandlungselement eingebaut ist,
sonst nach dem letzten Luftbehandlungselement mit einem Abstand
von mindestens 0,5 m
Als Ablufttemperaturfühler
direkt nach dem Luftaustritt aus dem Raum, in jedem Fall nach der
letzten Absaugöffnung, jedoch vor dem Ventilator. Es ist darauf zu
achten, dass die gesamte Abluft erfasst wird
Vorgehen bei der Montage
Zunächst Flansch montieren, siehe Abb. 1
QAM21xx.040: Fühlerrute von Hand (niemals mit Werkzeug) so
biegen, dass sie im montierten Zustand diagonal durch den Kanal
läuft,siehe Abb. 3
QAM21xx.200 und QAM21xx.600: Fühlerrute in Windungen mit
gleichmäßigem Abstand über den ganzen Kanalquerschnitt ziehen,
siehe Abb. 4
Achtung! Die Fühlerrute darf die Kanalwand nicht berühren, Min-
destabstand 5 cm. Ihr kleinster zulassiger Biegeradius ist 10 mm.
Die Fühlerhaut darf nicht verletzt werden!
Elektrischer Anschluß
Deckel lösen, siehe Abb. 2
Anschluss nach Anlageschaltplan
Installation
As a temperature detector for supply air or as a limiting sensor
after the supply fan, if it is mounted after the last air-treatment
element, i.e. heater or cooler battery
alternatively, after the last air-treatment element, at a distance of at
least 0,5 m from the element
As an extract air temperature sensor
immediately after the extract grill from the room of after the last
extract opening, but before the fan. Take care that all the extract air
is measured
As a dew-point sensor
directly after the washer
Mounting procedure
First mount the flange. See also figure 1
QAM21xx.040: Bend the sensing rod by hand (never wlth a tool)
such that in the mounted position it lies diagonally across the duct.
See figure 3
QAM21xx.200 and QAM21xx.600: Shape the sensing rod into the
form of a radiator, having equidistant arms, to cover the whole
cross-section of the duct. See figure 4
Attention! The sensing rod may not touch the wall of the duct; it ust
be at least 5 cm away. The smallest bending radius for the sensing
rod is 10 mm. The insulation on the sensing rod must not be
damaged!
Electrical connection
Remove the cover - see figure 2
Connect according to the system circuit diagram
Emplacement de montage
En tant que sonde de température de soufflage ou sonde de limitation:
après le ventilateur si celui-ci est monté après le dernier élément de
traitement de l'air;
sinon, après le dernier élément de traitement de l'air à une distance
d'au moins 0,5 m
En tant que sonde de température de reprise:
directement après la sortie de l'air du local, de toute façon après la
dernière bouche de reprise mais avant le ventilateur. Velller à ce
que l'ensemble du flux d'air participe à la mesure
En tant que sonde de point de rosée:
aussitôt après le séparateur de gouttelettes du laveur d'air
Marche à suivre
Monter tout d'abord la bride. Voir fig. 1
QAM21xx.040: courber la capillaire de la sonde à la main (jamais
avec un outil) de façon qu'il traverse en diagonale la gaine d'air une
fois la sonde montée. Voir fig. 3
QAM21xx.200 et QAM21xx.600: Etendre le capillaire de la sonde
sur toute la section de la gaine à intervalles réguliers Voir fig. 4
Attention! Le capillaire ne doit pas toucher la paroi de la gaine:
écartement minimal 5 cm. Plus petit rayon de courbe admis:
10 mm. L'isolation de la sonde ne doit pas être endommager!
Raccordement électrique
enlever le couvercle. Voir fig. 2
raccordement selon le plan de raccordement de l'installation
de
Montageanleitung
Kanaltemperaturfühler
en
Mounting instructions
Duct Temperature Sensor
fr
Instructions de montage
Sonde de température de gaine
sv
Monteringsinstruktion
Kanaltemperaturgivare
nl
Montage-aanwijzing
Kanaaltemperatuuropnemer
it
Istruzioni di montaggio
Sonda di temperatura de canale
fi
Asennusohje
Kanavalämpötila-anturi
es
Instrucciones de montaje
Sonda de la temperatura del canal
da
Monteringsvejledning
Kanaltemperaturføler
QAM21...
de
en
fr
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens QAM21 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens QAM21 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 0,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info