37687
9
Zoom out
Zoom in
Previous page
1/11
Next page
7
Gigaset AS150 / English / A31008-M1811-R601-3-TN19 / Wytana.fm / 05.05.2008
Care
Wipe the base station, charging cradle and handset
with a damp cloth (do not use solvent) or an anti-
static cloth.
Never use a dry cloth. This can cause static.
Contact with liquid
If the handset has come into contact with liquid:
1 Switch off the handset and remove the bat-
tery pack immediately.
2 Allow the liquid to drain from the handset.
3 Pat all parts dry, then place the handset with
the battery compartment open and the keypad
facing down in a dry, warm place for at least
72 hours (not in a microwave, oven etc.).
4 Do not switch on the handset again until it is
completely dry.
When it has fully dried out, you will normally be
able to use it again.
Questions and answers
If you have any queries about the use of your tele-
phone, go to
www.siemens.com/gigasetcustomercare
for assistance 24/7. The table below contains a list
of common problems and possible solutions.
Authorisation
This device is intended for analogue phone
lines in your network.
Country-specific requirements have been
taken into consideration.
We, Siemens Home and Office
Communication Devices GmbH & Co. KG,
declare that this device meets the essential
requirements and other relevant regulations
laid down in Directive 1999/5/EC.
A copy of the 1999/5/EC Declaration of
Conformity is available at this Internet
address:
http://www.siemens.com/gigasetdocs
.
Problem Cause Solution
Nothing
appears in the
display.
The handset is not
switched on.
Battery pack is
flat.
Press the end call
key
a for approx.
5seconds or place
the handset in the
base.
Charge/replace the
battery pack (page 2).
No response
to key press,
"HOLD KEY"
appears in the
display.
The keypad lock is
activated.
Press the hash key
R
for approx. 2 sec
(page 3).
No wireless
connection to
the base, dif-
ferent icons
flash in the
display.
The handset is
outside the range
of the base.
The handset is not
registered.
The base is not
switched on.
Cords not routed
correctly
Move the handset
closer to the base.
Register the handset
(page 4).
Check the power con-
nector at the base
(page 2).
Check cord routing
(page 2).
You cannot
hear a ring/
dialling tone
from the fixed
network.
The supplied
phone cord was
not used or it has
been replaced by
a new cord with
the wrong pin
assignment.
Please always use the
supplied phone cord
and ensure that the
pin connections are
correct when purchas-
ing a new one
(page 2).
!
Error tone
after entering
system PIN.
Forgot PIN
The system PIN
entered is incor-
rect.
Restore the system
PIN to the factory set-
ting (0000). To do this
disconnect the mains
unit
¢hold down the
paging-key ¢recon-
nect the mains unit
¢
hold the paging key
down for at least a
further 2 seconds
then release it.
The resetting proce-
dure is carried out.
The handsets are
deregistered. The
calls list is deleted.
Problem Cause Solution
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens Gigaset AS150 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens Gigaset AS150 in the language / languages: English as an attachment in your email.

The manual is 0,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens Gigaset AS150

Siemens Gigaset AS150 User Manual - German - 12 pages

Siemens Gigaset AS150 User Manual - Dutch - 10 pages

Siemens Gigaset AS150 User Manual - French - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info