526703
3
Zoom out
Zoom in
Previous page
1/8
Next page
3
INSTALLATION INSTRUCTIONS
For Safety Warnings & Operating Instructions of oven (R-2B34) refer to the Operation
Manual included inside the oven.
Refer to the Installation Diagrams on page 8.
1. The mains plug must be accessible after installation or the oven must be connected to an electric
circuit provided with an all-pole switch (contact gap no less than 3 mm) to disconnect the oven in
case of danger. A safety-device like a fuse in the installation may be used as a switch.
2. Remove the built-in kit mounting brackets from the package.
3. EBR-2610/EBR-2612 (500 mm cupboard) (Fig. 1, page 8)
Position the two oven runners (B) with the front hooked over the front edge of the shelf and pressed
against the right and left walls of the kitchen cabinet.
EBR-2620/EBR-2622 (600 mm cupboard) (Fig. 2, page 8)
Position the two oven runners (B) with the front hooked over the front edge of the shelf and using the
top mounting brackets (C) as spacers, press against the right and left walls of the kitchen cabinet.
Attach the oven runners with the four screws (E) as shown in Figs. 1 and 2 (page 8).
4. Attach the two top mounting brackets (C) to the ceiling of the kitchen cabinet with the two tabs
firmly pressed against the front face, as shown in Figs. 1 and 2 (page 8). Secure each bracket with
two screws (E).
5. Remove adhesive protection and attach the cushion (D) to the rear of the oven, as shown in Fig. 3
(page 8). FIT CLOSE TO, BUT DO NOT COVER THE AIR INLET HOLES (8) ON THE REAR OF THE
OVEN.
6. Place the oven (1) onto the oven runners (B). Locate the front feet (5) into the recess of the oven
runners (3) as shown in Fig. 5 (page 8).
7. Connect the oven to the power supply.
Caution: Make sure that the power supply cord (4) does not cross over the cushion (D) as shown in
Fig. 3 (page 8).
8. Place the built-in frame (A) over the oven (1) and engage the top mounting brackets (C) as shown in
Fig. 4 (page 8). (Note: the cutouts for the screws go to the bottom.)
Gently press the top of the frame down into the brackets, until the bottom of the frame engages
under the oven and the oven runners (B) as shown in Fig. 5 (page 8).
9. Fasten the frame with two screws (F) secured from the underside into the oven runners (B) as shown
in Fig. 5 inset (page 8).
NOTE: The R-2B34 is designed to be fitted and operated in a kitchen unit. Therefore it is not supplied
with a rear spacer. If for any reason, it is not operated built-in, ensure there is a minimum free
space above the oven of 15 cm and a minimum gap of 44 mm between the rear of the oven
and the adjacent wall, to provide air circulation.
GB
Diagram of oven position will be inserted here after completion of VDE testing.
As request in fax SEGCC-940 - the information for seperate sheet has been
inserted on this page.
R-2B34 B/I/K English 5/4/01 9:49 am Page 3
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp EBR-2610 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp EBR-2610 in the language / languages: English as an attachment in your email.

The manual is 2,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info