743716
4
Zoom out
Zoom in
Previous page
1/15
Next page
sharkclean.comsharkclean.com
BASE SETUP
The Self-Empty Base charges your robot and holds dirt and debris from up to 30 days of cleaning. Select a
permanent location for the base, because every time you relocate it, your robot will be required completely
re-map your house.
Choose a level surface in a central area. Remove any objects that are closer than 3 feet from either side of
the base, or closer than 5 feet from the front of the base. Plug in the Charging Cord, and turn on power
switch on the back of the base, then place the base with its back against the wall, in an area with a good
Wi-Fi signal. For best results, set up base on bare floor, or on the SharkMat. The base must be plugged in
continuously for the robot to find it. The Indicator Light will illuminate green when the base has power.
INSTALLING THE SIDE BRUSHES
Snap the 2 included Side Brushes onto the square
pegs on the bottom of the robot.
Clean Dock
!
If the robot has no charge and cannot return to
the base, manually place it on the base. The base
indicator light will flash blue and the robot will
beep when charging begins.
When the cleaning cycle is complete, or if the battery
is running low, the robot will search for the base.
If your robot doesnt return to the base, its charge
may have run out.
CHARGING
IMPORTANT: The Shark iQ Robot® has a pre-installed rechargeable battery. Battery should be fully charged
before using. It may take up to 6 hours to fully charge.
To charge, the Power button on the side of the robot
must be in the ON position (I). The robot will beep
when charging begins.
NOTE: When manually placing the robot on the base, make sure the Charging Contacts on the bottom of the robot are
touching the ones on the base and the robot's dust bin is touching the debris intake on the base. While the robot is
charging, both blue LED lights will flash. When charging is complete, both blue lights will illuminate steadily.
NOTE: When picking up the robot be careful not to place fingers between the bumper and the base of the robot.
NOTE: For best results, set up on bare floor or thin carpet.
NOTE: Do not place base against baseboards, heating elements, or in direct sunlight.
NOTE: Every time the robot returns to the base, it makes a loud noise as it empties its debris. This is normal and should not
be a cause of concern.
5 ft.
3 ft.
3 ft.
SharkMat
(for use on carpet)
4


Need help? Post your question in this forum.

Forumrules
1

Forum

shark-iq-robot-av1010ae-series

Reset search

  • One of the little brushes fell off. I have the brush but what holds it ther is missing, how do i get another to replace Submitted on 27-4-2024 at 03:31

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Shark IQ Robot AV1010AE Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Shark IQ Robot AV1010AE Series in the language / languages: English as an attachment in your email.

The manual is 3,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info