Manual Sentry EF4738E - Executive Fire-Safe (page 3 of 12) (English, French, Spanish)

651328

Zoom out

Zoom in

1/12

We are pleased that you have chosen one of our gun safes to protect your

ﬁrearms. You can be assured that your safe meets the California Department

of Justice standards for ﬁrearm safety. This manual will provide you with the

information you need to:

• unpack and set up your safe

• open the safe

• operate the lock

• take full advantage of your safe’s special features.

Remember to keep your combination a secret. Writing down a combination

and putting it in a desk drawer is like leaving your door key under the mat –

it invites entry.

Please retain this manual for your records. If you have any questions about

your gun safe, please visit our website at www.sentrysafe.com or call Sentry

Customer Service at 1-800-828-1438 or 1-585-381-4900. Customer Service

representatives are ready to assist you, 8 a.m. to 6 p.m., E.S.T., Monday - Friday.

Thank you for purchasing this SentrySafe gun safe product.

Please read this manual before using this product.

WARNING!

UNBOLTING YOUR GUN SAFE FROM THE SHIPPING PALLET

This is a two-person operation and should not be attempted without help. Before attempting to unbolt your new safe,

be certain someone is with you to help steady the safe while you work. Ensure the safe is standing upright on a ﬂat, level surface. (Fig. A)

NOTE: Sentry Group is not responsible for any costs incurred for unit to be removed from pallet and installed in place.

1. Using a wrench or pliers, remove the nuts located under the X-cut in the carpet in the bottom of the

unit. (Fig. B)

NOTE: If the bolts turn when you begin to remove the nuts, reach between the slats of the

pallet and hold the bolts, by hand and/or with pliers, as you turn the nuts.

2. Once the nuts are removed, use a hammer to tap the bolts through the bottom of the safe.

3. Close door and put handle in locked position.

4. With your helper, slide safe to one edge of pallet. Tip the safe so that the edge moves to the ﬂoor.

(Fig. C)

5. Remove the pallet and stand the safe upright on the ﬂoor.

Unbolting your gun safe from the shipping pallet

Tools/equipment required

• Adjustable wrench, pliers, or 17 mm (11/16”) socket wrench

• Hammer

Bolt-down instructions

To help provide maximum security, SentrySafe strongly recommends this safe be

bolted down. (Hardware supplied)

1. Select a suitable and convenient location for your safe. Set the safe in place and

use the holes provided in the bottom or back of the safe to mark the location

of the holes to be drilled in the ﬂoor or wall. It is not recommended to attempt

to bolt to both ﬂoor and wall. If bolting to a wall, please ensure that the safe is

resting ﬁrmly on the ﬂoor.

Note: Fire-Safe models cannot be bolted to the wall.

2. Move the safe away and drill holes of the appropriate diameter and depth for the

type of hardware and the mounting surface being used (2 each – bolts, washers

and masonry anchors).

3. Place the safe back over the holes and install the fasteners as required. If a water

resistant unit was purchased, rubberized washers are provided. Assure that the

area around the safe hole opening is clean using a damp cloth. Place the rubber

side of the washer facing down against the safe ﬂoor and install the fastener.

NOTE: SentrySafe is not responsible for any costs incurred if unit is to

be replaced.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sentry EF4738E - Executive Fire-Safe in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 1,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sentry EF4738E - Executive Fire-Safe Manual

Product: