651331
3
Zoom out
Zoom in
Previous page
1/9
Next page
2
3
Any Code + Any Code to unlock
1. Enter: # - Master Code - # - 1 - # - 1 - #
2. The lock will indicate a valid setting change
with a single signal.
Master or Manager Code + User Code to
unlock
1. Enter: # - Master Code - # - 2 - # - 2 - #
2. The lock will indicate a valid setting change
with a single signal.
Opening your safe in dual user mode
1. Enter: * - 1st Code - # - 2nd Code - #
2. The lock will indicate a valid code entry with
a single signal and the open light will stay
green for five (5) seconds.
3. Turn the handle clockwise before the green
light disappears
Returning to single user mode
(Single code to unlock)
1. Enter: # - Master Code - # - 0 - # - 0 - #
2. The lock will indicate a valid setting change
with a single signal.
Dual user mode
For additional security set your safe to dual user mode. This feature requires one user to enter their code and within sixty (60) seconds, a second user must
enter thier code to unlock the safe.
Always perform this operation with the door open.
4
Activate time delay
1. Enter: # - Master Code - # - (01-99) - # -
(01-99) - #
2. The lock will indicate a valid setting change
with a single signal.
Example: # - Master Code - # - 05 - # - 05 - #,
this will set a five (5) minute time delay.
3. Press * or # to initiate the Time Delay.
When time delay is set
(During the time delay period the keypad will
not respond to any entries)
The lock will flash once every five (5) seconds
during time delay and will flash once every
second during the last ten (10) seconds of the
time delay ending with a double signal.
The lock will flash twice every five (5) seconds
during the open period. The open period length
is two (2) minutes.
During the open period you can unlock or
program your safe.
Deactivate time delay
1. Enter: # - Master Code - # - 00 - # - 00 - #
2. The lock will indicate a valid setting change
with a single signal.
Time delay mode
Always perform this operation with the door open.
This function will delay both the opening and programming of the lock.
5
This kit contains:
• Four (4) Masonry Anchors
Required tools:
• Safety Glasses
• Powered Drill
Adjustable Wrench
• 1/2 in. (M12) Masonry Drill
Instructions:
1. Unlock safe and open door.
2. Remove safe floor carpet.
3. Look on the bottom of safe for four (4)
holes with cap plugs.
4. Remove the cap plugs.
5. Position the safe in the desired location.
6. From inside the safe mark the location of
the four (4) bolt down holes.
7. Move the safe aside to the clear marked
spots for drilling.
8. Using the ½ in. masonry drill, drill a 4 in.
deep hole in the marked locations.
9. Replace the safe in the desired location
with the holes in the safe aligned with the
drilled holes in the floor.
10. Pass each masonry anchor through the safe
floor into the drilled holes; making contact
with the safe floor.
11. Tighten each masonry anchor with the
adjustable wrench.
12. Replace safe floor carpet.
Floor Mount (optional)
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sentry DH-134E - Depository Safe at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sentry DH-134E - Depository Safe in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 0,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info