1. Place the prepared dough on to the hopper B2. Slide the cookie maker B15 to the left or
right to set the desired cookie shape.
2. Insert the power plug into apower socket. Set the required speed using the speed control
knob A12. When starting it for the rst time, we recommend that you set speed 3 and then
increase or decrease it as required.
3. Use the pusher B1 to push the dough through the feed tube B3. The food processor will
push the dough out in the required shape that you set using the cookie maker B15.
We recommend that you place atray or your palm underneath the pushed out dough. Then
cut the formed dough into smaller pieces.
Attention:
Do not use ngers or other items to push the dough in. Always use the
pusher B1.
4. When you have nished using the food processor, turn it o by setting the speed control
knob A12 to the OFF position.
5. Clean out the attachment after each use according to the instructions in chapter Cleaning
and maintenance.
BLENDING
ASSEMBLING AND DISASSEMBLING THE BLENDER
1. On to the blending jar C4, place the outer lid C2 so that its edges copy the neck of the jar,
and push it down thoroughly along its entire perimeter. Into the hole in the lid C2, place the
inner cap C1 and push it down all the way.
2. Make sure that the food processor is turned o and disconnected from the power socket.
The multi-function head A7 must be tilted down in the horizontal position and the whisk,
beater or kneading attachments must be removed. Release and remove the top attachment
hub cover A6. Place the assembled blending jar on to the top hub and pulling it gently
turn it in the direction of the symbol all the way. The safety mechanism will prevent the
blender from starting unless it is correctly secured to the multi-function head A7.
3. To disassemble proceed in the reverse sequence.
USING THE BLENDER
1. The blender is intended for preparing meals and drinks such as milkshakes, creamy soups,
sauces, spreads, fresh baby foods, etc. It is not intended for juicing fruit and vegetables,
preparing potato purée, yeast dough or for whipping egg whites.
2. Assemble the blender according to the instructions in chapter Assembling and
disassembling the blender, and put the ingredients (larger pieces need to be cut up in
advance) into the blending jar C4.
Note:
The maximum capacity of the blending jar C4 is 1.5 litres. Never ll it past
the maximum mark. When processing hot liquids or liquids that expand in
volume during the blending process, it is recommended to ll the blending
jar to no more than ⅔ of its maximum capacity.
3. Make sure that the food processor is correctly assembled and that the speed control knob
A12 is set to the OFF position. Connect the power cord to apower socket. Set the required
speed using the speed control knob A12. We recommend to rst set aslower speed to
allow the ingredients to mix together. Then the speed may be increased. The pulse level
is appropriate when you wish to blend food only very quickly. To start the pulse level, turn
the speed control knob A12 to the PULSE position and hold it in this position for amoment.
As soon as you release the speed control knob A12, it will automatically return to the OFF
position.
Attention:
Hot liquids up to atemperature of 55 °C may be processed in the blending
jar. The maximum operating time of the blender is 2 minutes. Do not leave
the appliance in continuous operation for longer than indicated above. Then
allow it to cool down for 30 minutes.
4. While blending, you may add food or liquids to the blending jar C4 through the hole in the
lid C2 after removing the inner cap C1. Never open the outer lid C2 during operation. When
processing hot liquids, the inner cap C1 must remain closed.
5. In the event that food is sticking to the blade assembly C6 or the walls of the blending jar
C4, turn the appliance o by turning the speed control knob A12 to the OFF position and
disconnect it from the power socket. Make sure that the blade assembly C6 has stopped
rotating. Carefully remove the assembled blending jar from the multi-function head A7 by
turning it in the direction of the symbol . Take o the lid and using aplastic spatula,
clean the blade assembly C6 and the inside of the blending jar C4. Put the lid back on and
reattach the blender assembly to the multi-function head A7. Plug the power cord into
apower socket and continue blending.
6. After you have nished using the appliance, set the speed control knob A12 to the OFF
position and disconnect the power cord from the power socket. Check that the blade
assembly C6 has stopped rotating and carefully take the blending jar assembly o the multi-
function head A7. Put the cover A6 back in its place and use asoft plastic spatula to remove
food from the blending jar C4.
7. Disassemble the assembled bowl and clean the individual parts after each use according to
the instructions in chapter Cleaning and maintenance.
ADVICE AND TIPS FOR BLENDING
■ First cut food with arm consistency such as fruit and vegetables into smaller pieces
measuring 3 cm and only then blend it.
■ First, blend asmaller amount of ingredients and then gradually add more ingredients
through the hole in the lid C2 while blending. In this way, you will achieve better results
than by adding all ingredients into the blending jar C4 at once.
■ If you need to blend food of asolid consistency together with liquids, we recommend that
you rst blend the food of solid consistency and apart of the liquids. Then gradually add the
remaining liquids through the hole in the lid C2 while blending.
■ To blend very thick liquids, we recommend using the pulse level so that the blade assembly
C6 does not get jammed too often. Start the blender repeatedly in short intervals.
■ Ice cubes must be processed immediately upon being removed from the freezer. When the
ice starts to melt, the ice cubes will stick together and it will not be possible to blend them.
QUICK GUIDE TO PROCESSING INGREDIENTS
IngredientsSpeed selectionRecommended
blending time
Fruit, vegetables cut into smaller pieces5–630 s
Baby food5–640 s
Spreads, dressings, marinades3–430 s
Smoothies and cocktails6 to MAX40 s
Soups6 to MAX30 s
Ice cubesPULSE
Note:
The above food processing times are only areference. The actual blending
time depends on the size of the ingredients, their amount and the required
nal consistency.
CLEANING AND MAINTENANCE
■ Before cleaning the food processor, always switch it o by setting the speed control knob
A12 to the OFF position and disconnect it from the power socket.
■ Disassemble the food processor into its individual parts. Wait until moving parts come to
acomplete stop before disassembly.
■ Thoroughly wash the used removable parts after every use using warm water with aneutral
dishwashing detergent. Then rinse them under clean running water and wipe them dry with
ane wiping cloth or allow them to dry naturally. After washing and drying, we recommend
to coat the grinding blade B6 and the grinding plates B8, B9 andB10 with cooking oil.
■ If you whisked egg whites, rst rinse the bowl A10 and the beater A4 under cold water.
If you were to use hot water, the egg white remains would harden and their removal would
be more dicult.
■ Clean the mixing container C4 by lling it with 0.5 litre of clean water and afew drops of
kitchen detergent and then assemble the blender and run it for 10 to 15 seconds. Then turn
o the food processor, disconnect it from the power socket, and after the rotating parts have
come to astop, remove the blending jar assembly. Empty out the contents of the blending
jar C4 and then thoroughly rinse out the blending jar C4 with clean water and wipe dry.
■ If more thorough cleaning is required, the cu C5 with blade assembly C6 may be removed
using aspecial wrench that can be ordered free of charge at an authorised service centre.
After cleaning, it is necessary to install the cu C5 with blade assembly C6 back in its place
and to properly tighten it using the wrench.
Attention:
When cleaning, be very careful not to injure yourself on the sharp cutting edge.
■ The metal parts of the meat grinder, the blade assembly C6 and attachments A3–A5
are not intended for washing in adishwasher. Other removable parts may be washed in
adishwasher.
■ For cleaning the base unit A11 and the multi-function head A7, use acloth lightly dipped
in aweak detergent solution. Then wipe everything with aclean dampened cloth and
thoroughly wipe dry.
■ For cleaning, do not use solvents or cleaning agents with abrasive eects. Otherwise, the
surface of the appliance may be damaged.
■ Do not submerge the food processor or its power cord in water or any other liquids.
STORAGE
■ When not using the food processor, store it in aclean, dry place out of children’sreach.
Make sure that the multi-function head A7 is tilted down into the horizontal position.
TECHNICAL SPECIFICATIONS
Rated voltage range ...............................................................................................................................220−240 V
Rated power input ........................................................................................................................................1 000 W
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Sencor STM 6359 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Sencor STM 6359 in the language / languages: English as an attachment in your email.
The manual is 1,1 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
