Do not wash the dust container or the dust filter in adishwasher.
Before putting the vacuum cleaner back into operation, check
that the dust filter is in its location. Otherwise the vacuum cleaner
may be damaged.
■Assemble all the parts to the initial state and slide the dust container back into the
vacuum cleaner.
WATER TANK
■We recommend that water is poured out of the water tank A4 and the tank is cleaned
after every wiping of the floor.
■Press latch D1 to slide the water tank out from the vacuum cleaner and then remove
the holder D3 with the mop fabric D4 from the water tank.
■Flip open the rubber cap D2 and pour out any remaining water.
■Use adamp cloth to wipe the entire tank and allow it to dry naturally. Do not expose
the water tank to direct sunlight while drying it.
Attention:
Do not wash the water tank, holder or mop fabric in adishwasher.
MOP
■After every dry or wet wiping, remove the mop fabric from the holder, wash it by hand
in lukewarm water with the addition of asmall amount of gentle washing powder and
allow it to dry naturally.
■Wipe the mop holder with alightly dampened cloth or wash it under running water
and then dry thoroughly.
CENTRAL ROTARY BRUSH
■Push on the latches F1 of the central rotary brush cover A21 and take out the cover.
■Take out the rotary brush A22.
■Use adry wiping cloth to clean out the area in which the rotary brush is housed. Also
clean the suction hole, the procedure is described later in this user'smanual.
■Remove any dirt and material (dust, wound on hair, animal fur, etc.) from the brushes
F2 of the rotary brush and also from the ends F3. You can cut heavily wound on hair
using the blade of the cleaning brush E2.
■Reinsert the rotary brush and its cover.
Attention:
In the event that an excessive amount of dirty material
accumulates on the central rotary brush and in its compartment,
there is arisk of permanently damaging the vacuum cleaner.
Regularly inspect the condition of the brush.
Do not use the vacuum cleaner without the central rotary brush.
SUCTION HOLE
■The suction hole is located underneath the central rotary brush, therefore, take it out
before cleaning the suction hole as described in the previous chapter. With repeat
use, dust and dirt may accumulate around the suction hole, which may manifest itself
through decreased suction efficiency. Remove the dirt and dust from the suction
hole using asoft brush. Regularly clean the suction hole to ensure maximum suction
power.
SIDE ROTARY BRUSHES
■Take out the rotary brushes by pulling them upwards. Remove any dust and dirt from
the location where the brushes were mounted.
■Remove all dust and dirt from the brushes. If necessary you may wash the brushes
under running water. If the bristles were deformed while the vacuum cleaner was
running, dip them in warm water to allow them to return to their original shape. Allow
the brushes to dry before reattaching to the vacuum cleaner.
■After cleaning it, reattach it.
Note:
The rotary brushes become worn out when used. After acertain time it
is necessary to replace the used brushes with new ones. To order new
brushes, contact your vendor or an authorised service centre.
COMPLETE ROBOTIC VACUUM CLEANER
■Regularly wipe the surface of the vacuum cleaner using asoft dry wiping cloth.
■First remove any coarser dirty material from the front swivel wheel A18 and the
motorised wheels A13 and A20. Then clean them around their entire perimeter using
alightly dampened cloth and wipe them dry. Do not forget to also clean the area
around the wheels.
■At least once per week, or more often, wipe the sensors A9, A12, A19 on the
underside of the vacuum cleaner and the side sensor A8 using asoft dry wiping cloth
or acotton bud.
CHARGING STATION
■At least once per week, clean the surface of the charging station B1 including the
charging contacts B2 using asoft dry wiping cloth.
STORAGE
When not using the vacuum cleaner for an extended period of time, do the following:
■Turn off the vacuum cleaner by setting the main switch to the OFF position.
■Clean the vacuum cleaner as described in chapter CLEANING AND MAINTENANCE.
■Disconnect the charging station from the power socket.
■Store the vacuum cleaner with all its accessories in adry, clean and cool place.
TECHNICAL SPECIFICATIONS
Robotic vacuum cleaner
Dimensions (diameter × height) ......................................................................................340 × 90 mm
Weight ...........................................................................................................................................................3 kg
Motor power output ..............................................................................................................................40 W
Operating time per single charge.....................................................................................up to 90 min
Dust container capacity ....................................................................................................................250 ml
Water tank capacity ............................................................................................................................350 ml
Vacuuming system .......................................................................................SUPER SUCTION 4 000 Pa
Navigation system ..........................................................................................................Sencor Nav. 16.0
Power adapter
Input ..........................................................................................................100–240 VAC, 50/60 Hz, 0.2 A
Output..........................................................................................................................................5 V, 1000 mA
Battery
Type ......................................................................................................................................2,600 mAh Li-Ion
Charging time ..........................................................................................................................................4–6 h
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Sencor SRV 8550 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Sencor SRV 8550 in the language / languages: English as an attachment in your email.
The manual is 0,73 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
