Manual Sencor SPR 3900 (page 13 of 14) (English)

758984

Zoom out

Zoom in

1/14

- 13 - 06/2019

LID GASKET

■ Gently pull the gasket A9 around the entire perimeter to remove it from the holder A13. Carefully wash the gasket in warm water with asmall

amount of kitchen detergent. Rinse with clean water and wipe thoroughly until dry. In reverse sequence, carefully insert the gasket back behind

the holder.

■ If the gasket is worn out or damaged, replace it with anew gasket of the same type.

PRESSURE CONTROL VALVE

■ Carefully pull the pressure valve cover A12 from the underside of the lid, see fig. D. In the event that the cover cannot be removed by hand, use

asuitable flat screwdriver and carefully release the cover. Wash the cover in hot water with detergent, rinse it and dry it thoroughly.

■

Using adamp cloth or soft brush, clean the inner part of the pressure valve D1 and dry it with adry wiping cloth. Push the cover back on to the valve.

■ Carefully pull out the steam release valve A7 from the outer side of the lid. Wash the valve, rinse and dry thoroughly.

■

Using adamp cloth or soft brush, clean the outer part of the pressure valve D2 and dry it with adry wiping cloth. Push the cover back on to the valve.

SAFETY FLOAT VALVE

■ Carefully remove the cover E1 of the safety float valve A11 from the inner side of the lid. Remove the valve from the hole in the lid. Wash the

cover and the valve in hot water with detergent, rinse them and dry them thoroughly.

■ Insert the valve into the hole in the lid and from the underside of the lid, slide the cover on to the valve.

Attention:

Never use the pressure cooker without the safety float valve cover or with adamaged cover.

Attention:

Before connecting the power cord into apower socket and into the pressure cooker and before turning the pressure cooker on

again, allow all surfaces to cool down completely.

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE REMEDY

The pressure cooker cannot be

turned on. The power is not connected Check the connection of the power cord, plug and

the power socket.

The lid cannot be closed. The lid gasket is not seated correctly. Check the position of the gasket.

The lid cannot be opened. There is still pressure inside the pressure cooker.

Release the pressure from the pressure cooker by

turning the steam release valve to the release position

or release the steam manually using button A2.

The lid cannot be opened after the

steam has been fully released. The safety float valve is still in the hole in the lid. Using asuitable tool (e.g. skewer) push the valve into

the down position.

Alarge amount of steam is escaping

around the edge of the pressure

cooker.

The lid is not properly closed. Check the correct installation of the gasket in the lid.

The lid gasket is not in its place or is soiled by food

remains. Position the gasket correctly on the lid or clean it.

The lid gasket is worn out or damaged. Replace the damaged gasket with anew one of the

same type.

The lid is damaged or deformed (e.g. by falling on

the floor). Contact the service department.

Large amount of steam is escaping

from the safety float valve.

There are food remains on the lid gasket. Remove the gasket from the lid and clean it.

The lid gasket is worn out or damaged. Replace the damaged gasket with anew one of the

same type.

Steam is continuously escaping

through the steam release valve

even when it is in the cooking

position.

Valve fault. Contact the service department.

The hotplate is not heating.

The lid is not properly closed. Close the lid in the proper manner.

The hotplate is faulty or the power circuit is

defective. Contact the service department.

Code E1 is flashing on the display. Faulty bottom sensor.

Contact the service department.

Code E5 is flashing on the display. Open lid circuit sensor fault.

Code E6 is flashing on the display. Open lid circuit sensor short circuit.

Code E8 is flashing on the display. Faulty pressure sensor.

Code E11 is flashing on the display. Communication fault between the control and

starting printed circuit boards.

Code E12 is flashing on the display. Communication fault between the receiving and

starting printed circuit boards.

Code E13 is flashing on the display. Float sensor short circuit

Code E14 is flashing on the display. Float sensor fault

Code E15 is flashing on the display. Thermal sensor fault on the receiving printed

circuit board.

Code E17 is flashing on the display. Receiving printed circuit board error.

Code E18 is flashing on the display. Starting printed circuit board error.

The text Pot is flashing on the

display. The removable pot is not inserted. Insert the removable pot into the built-in pot.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SPR 3900 in the language / languages: English as an attachment in your email.

The manual is 1,27 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sencor SPR 3900 Manual

Product: