759970

Sencor SHP 8400 Manual

8
Zoom out
Zoom in
Previous page
1/9
Next page
08/2018
- 8 -
Copyright © 2018, Fast ČR, a.s.
EN Hair Clipper
User'smanual
■ Prior to using this appliance, please read the user’smanual thoroughly, even in cases,
when one has already familiarised themselves with previous use of similar types of
appliances. Only use the appliance in the manner described in this user’smanual.
Keep this user’smanual in asafe place where it can be easily retrieved for future use.
In the event that you hand this appliance over to somebody else, make sure to also
include this user’smanual.
■ Carefully unpack the appliance and take care not to throw away any part of the
packaging before you find all its parts. We recommend saving the original cardboard
box, packaging material, purchase receipt and responsibility statement of the vendor
or warranty card for at least the duration of the legal liability for unsatisfactory
performance or quality. In the event of transportation, we recommend that you pack
the appliance in the original box from the manufacturer.
DESCRIPTION OF THE HAIR CLIPPER AND ITS ACCESSORIES
A1 Cutting blade, width 46mm
A2 Stainless steel cutting unit
A3 Cutting height adjustment lever
Enables cutting heights of 0.8 mm,
1.5 mm, 2.2 mm, 2.8 mm and 3.6
mm to be set.
A4 Hair clipper On/Off switch
A5 LED charging indicator
A6 Ergonomically-shaped handle
A7 Power adapter connection socket
A8 Power adapter
A9 Power adapter plug
B1 Comb attachment No. 1, cutting
height of 3mm
B2 Comb attachment No. 2, cutting
height of 6mm
B3 Comb attachment No. 3, cutting
height of 9.5mm
B4 Comb attachment No. 4, cutting
height of 13mm
B5 Comb attachment No. 5, cutting
height of 16mm
B6 Comb attachment No. 6, cutting
height of 19mm
B7 Comb attachment No. 7, cutting
height of 22 mm
B8 Comb attachment No. 8, cutting
height of 25mm
B9 Cleaning brush
B10 Oil for lubricating the cutting unit
B11 Travel case
D1 Comp part of attachment
D2 Heel of attachment
PURPOSE OF USE
■ The hair clipper is suitable for cutting dry or lightly dampened hair or beards. The
hair clipper is not intended for cutting freshly washed hair, clipping synthetic hair
or animal fur. The hair clipper is intended for domestic use and is not intended for
business activities or other professional areas of use.
CHARGING THE HAIR CLIPPER
■ The hair clipper is equipped with abuilt-in Lithium-ion battery, which serves as an
internal power source and enables cordless operation of the hair clipper. Before first
use or after not using it for along time, first allow the hair clipper battery to fully
recharge. Only use the original power adapter A8 to charge the hair clipper.
■ Check that the hair clipper is turned off and insert the power adapter plug A9
into the socket A7. Insert the mains plug of the power adapter A8 into apower
socket. The built-in battery will start charging after connecting the hair clipper to
apower socket. LED indicator A5 will start flashing red, which indicates charging.
The first charge takes approximately 3 hours. Thanks to rapid charging technology,
subsequent charging of the batter to full capacity takes approximately 2 hours.
■ As soon as the battery is fully charged, the indicator A5 will stop flashing and will
remain lit. Pull the mains plug of the power adapter A8 out of the power socket
and only then disconnect the power adapter plug A9 out of the socket A7. When
the hair clipper is disconnected from the external power source, the LED indicator
A5 will turn off.
Attention:
Do not leave the hair clipper connected to the external power
source for longer than is necessary to charge it.
■ Afully charged battery will provide approximately 1 hour of cordless operation. Then
it is necessary to charge the battery again.
■ Recommendations for achieving the longest possible battery lifetime:
– In order for the built-in battery to serve you as long as possible, charge, use and
store the hair clipper in adry environment at an ambient temperature of 15–35
°C. Lower or higher temperatures have anegative impact on the lifespan of the
battery.
– Do not wait for the battery to become completely flat. It is better to charge the
battery before it is completely flat.
– When the hair clipper is not used for an extended period of time, charge it at least
once every 6 months.
DIRECT DRIVE TECHNOLOGY
■ The hair clipper is equipped with DIRECT DRIVE technology, which enables the hair
clipper to be used immediately upon being connected to the mains power socket
even when the battery is completely flat. Therefore, it is not necessary to wait for
aminimum charge. If the hair clipper stops working due to the battery becoming
flat while cutting hair, you can connect it to the mains power grid using the power
adapter A8 and continue cutting.
USING THE HAIR CLIPPER
PREPARATION BEFORE THE HAIRCUT
■ Only use the hair clipper on dry clean hair or lightly dampened hair. Do not use it on
wet and freshly washed hair or hair with gel applied on to it, etc. Trim beards when
they are dry without the use of shaving gels or foams.
■ Before starting any styling of hair or beards, acquaint yourself with the operating
instructions.
■ Seat the person whose hair you will be cutting in such away that their head is at
the height of your chest. This will provide for acomfortable cutting position. Before
cutting hair, thoroughly comb out the hair in the growth direction.
■ Cover the neck and shoulders of the person whose hair you will be cutting with
atowel to limit cut hair from falling on their clothes.
■ Prior to every use, check that the cutting blade A1 is clean.
■ Prior to every use, check the cutting unit A2 and the selected comb attachment for
damage. Never use ahair clipper with adamaged cutting unit or comb attachment.
SETTING THE CUTTING HEIGHT
■ Before the height is set, the hair clipper must be turned off using switch A4.
■ The height adjustment lever A3 has 5 positions, which enable the cutting height
to be adjusted to 0.8 mm, 1.5 mm, 2.2 mm, 2.8 mm and 3.6 mm. Moving it to any
position (figure C) is accompanied by an audible click.
- to lower the cutting height, move the lever upwards.
- to increase the cutting height, move the lever downwards.
TURNING THE HAIR CLIPPER ON AND OFF
■ Turn on the hair clipper using switch A4.
■ When you have finished using it, always turn the hair clipper off using switch A4 and
disconnect it from the power socket if it was powered from amains power socket.
Then clean it out according to the instructions in chapter Cleaning and maintenance.
Attention:
The maximum continuous operating time of the hair clipper
is 30 minutes, so do not leave it running for longer. If the hair
clipper was in continuous operation for 30 minutes, allow it to
cool down for at least 30 minutes before turning it on again. At
lower loads, acooling time of 3 to 5 minutes is usually sufficient.
USING THE HAIR CLIPPER WITH ACOMB ATTACHMENT
■ The hair clipper comes with comb attachments B1 to B8 for various cutting heights.
Information about the cutting height is shown on each of the attachments. Select
one of the attachments and attach it to the cutting unit A2 according to the
instructions below.
Attention:
Put the comb attachments on to the cutting unit before turning
on the hair clipper and always turn the hair clipper off before
removing them.
■ First slide the comb part D1 on to the cutting blade A1 from above and then push
down the heel of the attachment D2 on to the bottom part of the cutting unit A2,
see figure D. Correct attachment of the attachments is accompanied by an audible
click. Check that the selected comb attachment is securely fitted to the cutting unit
A2.
■ Set the appropriate cutting height using the lever A3. If you are using the hair clipper
for the first time, it is recommended to first try alonger cut and only thereafter adjust
the setting to ashorter cut.
■ To remove the comb attachment, first release the heel of the comb attachment D2
and then slide the attachment off the cutting unit A2.
USING THE HAIR CLIPPER WITHOUT THE COMB ATTACHMENT
■ Before the height is set, the hair clipper must be turned off using switch A4.
■ You may use the hair clipper without acomb attachment to, for example, to trim
beards very close to the skin (0.8 mm) or to trim the neckline or the area around the
ears. Set the appropriate cutting height using the lever A3. If you want the cutting
height to be as short as possible, move the lever A3 upwards all the way. Hair will
be cut directly above the scalp. This setting is suitable for trimming hair on the neck
and around the ears.
■ Push the lever downwards as far as it will go to set acutting height of approximately
3.6 mm.
Attention:
The cutting blade A1 will cut off all hair, beards or nose and
ear hair that comes into contact with it, therefore be especially
careful when handling the hair clipper while it is running.
ADVICE AND TIPS
■ Start cutting with the highest cutting height set on the cutting unit A2 and gradually
reduce the hair cutting height setting.
■ Record the used height setting for certain hairstyles so that you do not need to
spend time adjusting it the next time.
■ It is most effective to cut counter to the direction of hair growth.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sencor SHP 8400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SHP 8400 in the language / languages: English as an attachment in your email.

The manual is 0,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info