759937
5
Zoom out
Zoom in
Previous page
1/6
Next page
- 5 - 07/2020
Copyright © 2020, Fast ČR, a.s.
EN Ceramic heater
User'smanual
Prior to using this appliance, please read the user'smanual thoroughly, even in cases,
when one has already familiarised themselves with previous use of similar types of
appliances. Only use the appliance in the manner described in this user’smanual.
Keep this user'smanual in asafe place where it can be easily retrieved for future use.
We recommend saving the original cardboard box, packaging material, purchase
receipt and responsibility statement of the vendor or warranty card for at least the
duration of the legal liability for unsatisfactory performance or quality. In the event
of transportation, we recommend that you pack the appliance in the original box
from the manufacturer.
DESCRIPTION OF THE APPLIANCE
A1 Operating mode selection knob
A2 On/Off indicator light
A3 Thermostat knob
A4 Front cover
A5 Rear cover
A6 Tip-over safety mechanism (located
on the underside of the heater)
BEFORE USING
Before first use, take the appliance and its accessories out of the packaging material
and remove all promotional labels and stickers. Check that neither the appliance nor
any of its parts is damaged.
CONTROLLING THE HEATER
Locating the heater
Locate the heater on an flat and solid surface at asufficient distance from the power
socket.
Insert the power plug into apower socket.
Turn the thermostat A3 clockwise until you hear aclick, which indicates that the
heater is turned on.
Set the thermostat to the desired level. Turning it clockwise (towards MAX) sets
a higher thermostat level and conversely, turning it anticlockwise (towards MIN)
sets alower thermostat level.
Turning off the heater
When not using the heater, turn knob A1 to the OFF position and turn the
thermostat A3 anticlockwise to MIN until you hear aclick. This indicates that the
heater is turned off. Disconnect the power plug from the power socket.
Note:
A slight odour may be felt when the heater is first turned on or after
an extended period where it has not been used. This will go away after
ashort while.
Setting an operating mode
Turn knob A1 to select the desired operating mode:
– fan mode
– 1,200 Whot air mode
– 2,000 Whot air mode .
When knob A1 is turned, the indicator light A2 will turn on and remain lit until the
knob A1 is set to the OFF position.
AUTOMATIC SAFETY SHUT-OFF FUNCTION
The ceramic heater is equipped with a safety mechanism A6 that automatically
turns it off when it is tipped over. This safety mechanism A6 serves asafety function
and prevents dangerous situations from arising.
OVERHEATING PROTECTION
In the event that the temperature of the heater is too high due to an inappropriate
environment in which it is used or as aresult of incorrect use, the power supply to
the heater will automatically be shut off and it will stop working. It is recommended
to disconnect the power plug from the power socket and allow it to cool down
completely. Then you will be able to use the heater again.
THERMAL PROTECTION
The ceramic heater is equipped with double thermal protection – aresettable and
non-resettable thermal fuse. The resettable thermal fuse will turn the heater off
when there is adanger of its overheating or malfunctioning. When the temperature
of the heater falls, you will be able to use the heater again.
The non-resettable thermal fuse is installed for the case, where the resettable
thermal fuse fails. In the event of overheating, malfunction or if the heater stops
working for any other reason, the non-resettable thermal fuse will completely turn
off the heater and it will not be possible to turn it on. In such acase, contact an
authorised service centre.
The most frequent cause of overheating is the accumulation of dust or dirt on the
rear grille A5 and on the the front grille A4. Regularly remove dust and dirt using
avacuum cleaner. Always turn off the heater, disconnect the power plug from the
power socket and allow the heater to cool down completely before cleaning it.
The heater is not equipped with a temperature sensor, therefore, it cannot be used
to heat areas designed for storage of objects that require a precise temperature
control.
MAINTENANCE AND CLEANING
Ensure that the appliance is turned off and that it has cooled down before cleaning
it.
Wipe the appliance using asoft dry cloth. Regularly remove dust and dirt from the
front A4 and rear grille A5. Avacuum cleaner can also be used for removing the dust
and dirt. Nevertheless, always check that the heater is turned off, the power plug is
disconnected for the power socket and that the heater has cooled down completely.
Do not use chemicals or abrasive cleaning products for cleaning. Otherwise the
surface of the appliance may be damaged.
Warning:
To prevent the risk of injury by electrical shock, do not submerge
the appliance, power cord or power plug in water or any another
liquid.
STORAGE
When not using the appliance, store it in adry, clean place out of children'sreach.
Allow the appliance to cool down before storing it.
TROUBLESHOOTING
When the heater does not work properly, first check the instructions provided
below, which will help you to resolve potential problems with the heater. If the
problem is not described in the instructions below or if the problem persists, stop
using the heater, disconnect the power plug from the power socket and contact an
authorised service centre.
Problem Cause Solution
After connecting it to
the power socket, the
indicator light A2 does
not light up and the
heater does not work.
The plug is not correctly
inserted in the power
socket.
Pull out and reinsert the
power plug into the power
socket.
You have not turned
the thermostat knob A3
sufficiently.
Turn the thermostat knob
A3 clockwise until you
hear aclick.
The heater suddenly
turns off during
operation.
The thermal fuse that
protects the appliance
against overheating was
triggered.
Turn off the heater,
disconnect the power plug
from of the power socket
and allow the heater to
cool down completely.
TECHNICAL SPECIFICATIONS
Rated voltage .................................................................................................................. 220 – 240 V~
Rated frequency............................................................................................................................. 50 Hz
Rated power input ................................................................................................................... 2,000 W
Noise level .................................................................................................................................. 60 dB(A)
The declared noise emission level of the appliance is 60 dB(A), which represents alevel
Aof acoustic power with respect to areference acoustic power of 1 pW.
Safety class for electrical shock protection:
Class II – Electrical shock protection is provided by double or heavy-duty
insulation.
We reserve the right to change text and technical specifications.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sencor SFH 7701 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SFH 7701 in the language / languages: English as an attachment in your email.

The manual is 0,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info