Manual Sencor SES 9200CH (page 11 of 12) (English)

758389

Zoom out

Zoom in

1/12

- 11 - 06/2020

MANUAL FLUSH

■ We recommend that you always clean the coffee spout when you have finished

using it. It is also recommended to do this when the appliance has not been used for

an extended period of time.

1. In the stand-by mode, simultaneously press and hold down buttons B7 andB9

for 5 seconds.

2. The lights of the touch buttons will turn off. Asmall amount of water will flow out of

the spout, which will flush it out. Water will flow into the drip tray A11.

Attention:

Avoid coming into contact with hot water.

3. After finishing the manual flush, the appliance will switch back to the stand-by

mode.

DRAIN INTERNAL LINES

■ It is recommended to drain the internal lines when you plan on not using the

appliance for and extended period of time, before transporting it, etc.

1. In the stand-by mode, simultaneously press and hold down buttons B7 andB11

for 5 seconds.

2. Indicator B6 will start flashing.

3. Remove the water tank A1 from the appliance. Indicator B6 will be lit. This

signals that the draining of the internal lines is running.

Note:

If you press button B7 before taking out the water tank A1, you will

return back to the stand-by mode.

4. When the internal line draining process is complete, the appliance will turn off

automatically.

CLEANING THE GROUND COFFEE OUTLET

■ During use, ground coffee may accumulate on the walls of the ground coffee outlet

and therefore it is necessary to clean it regularly (depending on the frequency of

use).

1. Slide out and remove the service access door A7. Press the steam unit release

buttons A6 and take out the steaming unit A6 – see figure H.

2. Carefully tilt the espresso machine and using brush A12, carefully remove any dirty

material from the walls of the ground coffee outlet – see figure K.

3. After cleaning it out, insert the steaming unit A6 and the service access door A7

back in their place.

Storage

■ When not using the appliance for an extended period of time, disconnect the power

plug from the power socket, allow the appliance to cool down and clean it according

to the instructions provided above.

■ Before storing it, check that the appliance and all its accessories are thoroughly

clean and dry.

■ Store the appliance in a dry, clean and well-ventilated location not exposed to

extreme temperatures and out of children'sreach.

TROUBLESHOOTING

Problem Cause Solution

The appliance is not

working.

It is not connected to

apower socket.

Connect it to aworking

power socket and press

button B7 .

Check that the power cord

A5 is properly connected to

the socket in the appliance

and that the plug is properly

inserted in the power socket.

There is no response

when abutton

is pressed or the

response is delayed.

Electromagnetic interference

of the appliance is occurring.

Turn off the appliance and

turn it back on again after

several minutes.

The touch panel is soiled. Turn off the appliance,

disconnect it from the

power socket and clean the

panel using aclean, lightly

dampened cloth and then

thoroughly wipe it dry.

Coffee is not warm

enough.

Cups have not been

warmed up.

Warm up the cups.

The steaming unit A6 is

too cold.

Flush out the spout three

times before brewing coffee.

Coffee is not flowing

out the spout.

Prior to this you used the

drain internal lines function.

Press the dispensing hot

water button until water

starts flowing from the

spout.

The first cup does not

taste particularly good.

There is an insufficient

amount of ground coffee

inside the steaming unit A6.

Pour out of the first coffee

that you brewed. The next

cup will now be in order.

The coffee lacks froth. The coffee beans are not

fresh.

Use fresh coffee beans or

try using adifferent brand

of coffee.

Touch buttons do not

function properly.

The touch buttons are not

pressed properly.

It is necessary to use the

appliance from the front.

Press the bottom part of the

icon of the touch button.

The appliance heats up

for too long.

The appliance is soiled by

limescale deposits.

Descale it according to the

instructions contained in

section "Self-clean function

(self-cleaning)".

The water tank A1

is removed or it is

running out of water,

but the respective

indicator is not

signalling anything.

The area around the

connector at the bottom of

the water tank A1 is damp

or wet.

Thoroughly dry out any

moisture or water in the

vicinity of the connector.

The inner drip tray A10

is filled with alarge

amount of water.

The coffee is ground too fine,

which prevents water from

flowing through.

While the coffee grinder

is running, set acoarser

grind level.

The coffee is supplied

too slowly or

intermittently.

The coffee is ground too fine,

which prevents water from

flowing through.

While the coffee grinder

is running, set acoarser

grind level.

The insufficient coffee

beans indicator is

flashing even though

there is asufficient

amount of coffee

beans in the hopper.

The internal ground coffee

outlet is clogged.

Clean out the ground coffee

outlet of the appliance

according to the instructions

in section "Cleaning the

ground coffee outlet".

No frothed milk is

coming out of the

appliance.

The automatic milk frothing

device is dirty or is not

correctly assembled or

installed.

Clean the automatic milk

frothing device and check

that it is correctly assemble

or installed.

The holes in connecting

tube A15 are clogged.

Clean out the connecting

tube A15 according to

the instructions in section

"Everyday cleaning and

maintenance – Milk jug,

milk tube and connecting

tube".

The holes in

connecting tube A15

are clogged and it is

difficult to remove

dirty material.

The connecting tube A15

has not been cleaned out in

along time.

Leave the connecting tube

A15 submerged in hot

water for approximately one

hour and then clean out

the connecting tube A15

according to the instructions

in section |"Everyday

cleaning and maintenance

– Milk jug, milk tube and

connecting tube", until

water flows continuously

through the brew head.

The type of milk used is not

suitable for frothing.

Froth made from various

types of milks differs as does

the quality of the resulting

froth. Half-cream or full-

cream cow'smilk delivers

good results.

Milk is being sprayed

on to the table.

The connecting hose A15 is

not correctly installed.

Install the connecting tube

A15 correctly. Proceed

according to instructions

in section "Setting up the

system for automatic

frothing".

The descaling process

indicator is flashing

continuously even

after the descaling

process is finished.

The descaling process is not

yet finished.

Please be patient and wait

for the process to finish.

The appliance will turn off

automatically, please do

not turn off this appliance

manually.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SES 9200CH in the language / languages: English as an attachment in your email.

The manual is 3,28 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sencor SES 9200CH Manual

Product: