Manual Sencor SCF 3200 (page 9 of 10) (English)

759221

Zoom out

Zoom in

1/10

- 9 - 08/2019

EN Convection heater

User'smanual

■ Prior to using this appliance, please read the user’smanual thoroughly, even in cases

where you have previously familiarised yourself with the operation of similar types

of appliances. Only use the appliance in the manner described in this user’smanual.

Keep this user’smanual in asafe place where it can be easily retrieved for future use.

■ We recommend saving the original cardboard box, packaging material, purchase

receipt and responsibility statement of the vendor or warranty card for at least the

duration of the legal liability for unsatisfactory performance or quality. In the event

of transportation, we recommend that you pack the appliance in the original box

from the manufacturer.

DESCRIPTION OF THE APPLIANCE

A1 Display with control elements

A2 Front panel

A3 Main power switch (located on the

side)

A4 Travel wheels

A5 Wall mounting hooks

A6 Rear panel

A7 Wall mounting set (not shown)

DESCRIPTION OF THE CONTROL PANEL

B1 Button ▲

B2 Button ▼

B3 On/Off/Child safety lock button

B4 Programming button

B5 Operating mode button

B6 Day of the week and hour setting

button

DESCRIPTION OF THE DISPLAY

C1 Power saving mode icon

C2 Frost-free mode icon

C3 Programming icon

C4 Hours

C5 Day of the week icon

C6 Timer icon

C7 Heating icon

C8 Comfort mode icon

C9 Temperature display

C10 Lock icon

C11 Hour icon

C12 Minute icon

C13 Heating display

BEFORE FIRST USE

■ Before first use, take the appliance and its accessories out of the packaging material

and remove all promotional labels and stickers. Check that neither the appliance nor

any of its parts is damaged.

INSTALLATION

■ The convection heater may be used as amobile heat source (necessary to install

the travel wheels A4) or it may be mounted on awall (travel wheels A4 must be

removed).

Warning:

Before any type of installation, always make sure that the power

plug is disconnected from the power socket.

Installing the travel wheels

■ Put ablanket or another soft underlay on the floor. Then place the convection heater

upside down on to this blanket.

■ On the underside of the convection heater there are three drilled holes on either

side. Align these holes with the holes in the travel wheels A4 and, using the supplied

self-tapping screws, screw them to the underside of the convection heater – see

figure D. Tighten securely. Check that the travel wheels A4 are correctly attached

to the convection heater.

■ Turn the convection heater over and carefully put it down on the travel wheels A4.

Check that the wheels move freely and that they are not blocked in any way.

Wall mounted installation

■ Before mounting the convection heater on awall, it is important that you check that

the installation location has no wires, conduits, pipes, etc. in the wall.

■ Likewise, prior to installation, remove the travel wheels A4 if they are installed.

■ Prior to installation, also check that the installation location is at asufficient distance

from the power socket.

Warning:

Only use the supplied set of screws and dowels for the

installation. Under no condition should dowels and screws be

used that have adifferent diameter, different specifications and

which are not approved by the manufacturer as suitable for the

installation of this type of product.

■ Drill holes of 8 mm diameter 40 mm deep into the wall as shown in figure E.

■ Insert the plastic dowel into the drilled hole and then the screw. Using ascrewdriver,

secure the screw and leave it protruding out approximately 6 mm.

■ Put the convection heater on to the wall by sliding the screw heads into the holes

on the hanging hooks A5.

Warning:

The convection heater must be installed at least 15 cm above the

ground and 50 cm from the ceiling. The convection heater must

be installed horizontally. Any electrical installations must be

performed by aqualified electrician. The convection heater must

not be installed behind doors or in an outdoor environment.

USING THE CONVECTION HEATER

■ Prior to first use, check that the voltage in your power socket corresponds to the

voltage on the rating label.

■ Insert the power plug into apower socket.

■ Set the main switch A3 to position I(On). Asound will be made and the display A1

will be lit for ashort moment. As soon as the display A1 turns off, the convection

heater will automatically switch to the stand-by mode.

Turning the convection heater on/off

■ If the open lock icon is lit on the display, press the On/Off button B3 to turn the

convection heater on.

■ If the closed lock icon is lit on the display, hold down the On/Off button B3 for

approximately 3 seconds to cancel the child lock function. When the icon changes

to the open lock , press the On/Off button B3 to turn the convection heater on.

■ When the convection heater is turned on, the temperature, time, day icon, child lock

icon and heating icon C7 will be lit.

■ When you have finished using it, press the On/Off button B3 and the convection

heater will turn itself off, however, it will remain in stand-by mode. To completely

turn off the convection heater, set the main switch A3 to position 0 (Off) and

disconnect the power plug from the power socket.

Note:

Upon first use or after it has not been used for an extended period of

time, aslight odour may be sensed or asmall amount of smoke may

be emitted from the convection heater. This is completely normal and

will quickly disappear.

Child safety lock

■ The child safety lock function enables the display with the control elements A1 to be

locked and prevents accidental changes to your settings.

■ To turn on the lock function, hold down the On/Off button B3 for approximately

3 seconds. The closed lock icon will be lit on the display. All the control buttons

will be disabled.

■ To cancel the child safety lock function, hold down the On/Off button B3 for

approximately 3 seconds, until the icon changes to the open lock .

Note:

The child safety lock function can be used even when the convection

heater is running, or alternatively when it is turned off in the stand-by

mode.

Selecting an operating mode

■ The convection heater has three operating modes: comfort mode, power saving

mode and Frost-free mode.

■ Repeatedly press the button B5 to toggle between the individual modes. The icon of

the selected mode (C1, C2 or C8) will be lit on the display A1.

■ When the convection heater is turned on, it will run in the power saving mode and

icon C1 will be lit.

Note:

If the heating icon C7 is lit on the display A1, this means that the

convection heater is running and is heating to the set temperature. As

soon as the temperature is reached, the heating icon C7 will turn off

and only the icon of the selected mode will remain lit.

The icon C7 will intermittently turn on and off while the convection

heater is running. This is normal. The convection heater is heating to

the set temperature.

Comfort mode – when the room temperature falls 2°C below the set temperature, the

heating icon C7 will be lit and the convection heater will start. The heating icon C7 will

remain continuously lit while the appliance is heating. When the temperature rises 2°C

above the set temperature, the heating icon C7 will turn off and the convection heater

will switch to the stand-by mode.

Power saving mode – when the room temperature falls 4 °C below the set

temperature, the heating icon C7 will be lit and the convection heater will start. The

heating icon C7 will remain continuously lit while the appliance is heating. When the

temperature rises 4°C above the set temperature, the heating icon C7 will turn off and

the convection heater will switch to the stand-by mode.

Frost-free mode – this mode prevents the freezing of the convection heater and

cooling of the room in which it is located. The convection heater will start automatically

when the ambient temperature falls to 5°C. As soon as the temperature rises above

7°C, the convection heater will turn itself off.

Setting the temperature

■ The buttons ▲/▼ are used to set the operating temperature. Press button ▲ or ▼

andthe numerical temperature value will start flashing. Use the buttons ▲/▼ to

set the desired temperature. To save the temperature, press the On/Off button B3

or wait approximately 10 seconds until the temperature value stops flashing. The

convection heater will automatically save the temperature setting.

■ You can set the temperature in the range from 15 to 35 °C.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SCF 3200 in the language / languages: English as an attachment in your email.

The manual is 0,5 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sencor SCF 3200 Manual

Product: