424986
17
Zoom out
Zoom in
Previous page
1/18
Next page
English
www.self-sat.com
16
If the signal is not found, be sure the receiver user manual and the antenna user manual have been
followed closely, check the following:
Make sure all cable connections are correct and each connection is seated/tightened properly
Inspect the inside of each cable connector for dirt or possible connector to case/shield short.
Verify the Azimuth, Elevation and Tilt angles for your location by ZIP code.
Make sure the Tilt and Elevation pointers are aligned correctly to the scales. Do not use washer or
bolt as reference.
Make sure the Tilt adjustment is not changed from the recommended setting for the antenna
location.
Remove existing TV-specic components, such as TV splitter, etc; reduce the installation to the basic
connections called out in this guide. Such components may not work with the satellite signal and
they may be in the wall where you can’t see them. When in doubt. Run RG6 cable directly to your
receiver
Make sure there are no obstructions (trees, buildings, windows, corner or overhang of your roof,
your body or hands) – the signal does not pass leaves, branches, glass, etc.
RG 6 cable with solid copper center conductor is highly recommended because it has much lower
DC voltage drop compared to RG 6 cable with a copper-coated, steel center conductor.
Standard RG 59 cable causes too much DC drop and signal drop; it can not be used to pass the
satellite signal. RG 6 coaxial cable must be used.
Some after-market, o-the-shelf add-on components may not be as advertised. They might not
work or could cause additional DC drops and signal amplitude attenuation. Remove such compo-
nents. Go back to the basic connections called out in this manual and re-verify.
Make sure the satellite cable is connected to the “Sat In” jack, not the “Antenna In” jack, The
“Antenna In” jack at the back of the receiver is for o-air antenna input or cable TV input.
If all are done correctly but the signal is still not found. Change the Elevation adjustment of the
antenna slightly (±2°, then ±4°from the called-for setting) and repeat the procedure.
Make sure the Access Card from your receiver is fully inserted into the Access Card slot and oriented
correctly.
Troubleshooting Check List for Initial Installation
SELFSAT-H10D/H21D
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Selfsat h21d at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Selfsat h21d in the language / languages: English as an attachment in your email.

The manual is 0,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Selfsat h21d

Selfsat h21d User Manual - German - 17 pages

Selfsat h21d User Manual - Dutch - 25 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info