Manual Scheppach DP19Vario (page 27 of 148) (English, German, French, Italian, Polish)

781654

Zoom out

Zoom in

1/148

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 27

Important: All bare parts are greased in order to pro-

tect them from corrosion. Before mounting the drill

chuck (12) onto the spindle, both parts must be com-

pletely degreased using an environmentally friendly

solvent. This ensures optimal transmission of power.

Installing the machine

Before you use the drill for the rst time it must be

mounted in a stationary position on a rm surface.

Use both mounting holes in the base plate to do this.

Ensure that the machine is freely accessible for op-

eration, adjustment and maintenance.

Important: The xing screws may only be tightened

to a point where they do not distort or deform the

base plate. Excessive tension can lead to fracture.

Prior to starting

Ensure that the voltage of the mains supply complies

with the specications on the rating plate. Connect

the machine only to a socket with the properly in-

stalled earthing contact. The table drill is equipped

with a no-volt trip that is designed to protect the

operator from an undesired restart following a drop

in voltage. Should this occur, the machine must be

manually restarted.

9. Operation

General (Fig.14)

To switch on the machine, push in the green On but-

ton “I” (9); the machine starts up. To switch off , press

the red Off button “O” (9); the device shuts down.

Ensure that you do not overload the device.

If the sound of the motor drops in pitch during opera-

tion, it is being overloaded.

Do not overload the device to the point where the mo-

tor comes to a standstill. Always stand in front of the

machine during operation.

Inserting the tool (Fig. 1)

Make sure that the power plug is removed from the

socket-outlet before changing tools. Only cylindrical

tools with the stipulated maximum shaft diameter may

be clamped in the scroll chuck (12). Only use a tool that

is sharp and free of defects. Do not use tools whose

shaft is damaged or which are deformed or awed in

any other way. Use only accessories and attachments

that are specied in the operating instructions or have

been approved by the manufacturer. If the pillar drill

should become jammed, switch off the machine and

return the drill to its starting position.

Handling the keyless chuck

Your pillar drill is equipped with a keyless chuck. This

enables tools to be changed without the need for an

additional chuck key. To do so, insert the tool in the

quick-change drill chuck and tighten by hand.

6. Place the hand crank (16) on the shaft of the drill-

ing table holder (4) and secure it with the Allen

screw. To do this, use the Allen key (B)

7. Screw one of the clamping handles (3) into the

drilling table holder (4).

Installing the machine head and column, Fig. 8

1. Place the machine head (13) on the column (2).

2. Align the drill’s spindle with the table and the

base plate and tighten the Allen screw that is lo-

cated on the side of the machine head. (Allen key

SW4 / A)

Installing the handles, Fig. 9+10

1. Screw three handles (10) tight in the handle brack-

et’s thread. Use the hexagon spanner to do this.

2. Screw the remaining handle (6) into the handle

bracket for speed adjustment. Use the hexagon

spanner to do this.

Installing the folding swarf protector and the drill

chuck, Fig.11

1. Push the folding swarf protector (11) onto the spin-

dle on the machine head and use a Phillips head

screwdriver to secure it.

Installing the chuck (g. 12)

1. Clean the conical hole in the drill chuck and the

spindle cone with a clean piece of cloth. Make sure

that no dirt particles stick to the surface. The slight-

est contamination on one of the surfaces prevents

the drill chuck from holding properly. This may

cause the drill to hit. If the tapered hole in the drill

chuck is extremely dirty, use a detergent on a clean

piece of cloth.

2. Push the drill chuck onto the spindle nose as far

as possible.

3. Turn the outer ring of the chuck counter-clockwise

(from the top view) and open the jaws of the chuck.

4. Place a piece of wood on the machine table and

lower the spindle down to the piece of wood.

Press rmly so that the feed ts strongly.

Insert/change battery: using the laser (g. 13)

1. Insert/change battery: Switch off laser. Insert or

remove the battery compartment cover (14.1). Re-

move batteries and replace with new (2 AA bat-

teries).

2. To switch on: Move the ON/OFF switch (14) to

the “I” position to switch on the laser. Two laser

lines are projected on the workpiece and intersect

at the center of the drill tip contact point.

3. To switch off: Move the ON/OFF switch (14) to

the “0” position.

Installing the laser (g. 13)

The laser can be adjusted using the adjusting screws

(F).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach DP19Vario in the language / languages: English, German, French, Italian, Polish as an attachment in your email.

The manual is 7.17 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach DP19Vario Manual

Product: