699901
7
Zoom out
Zoom in
Previous page
1/8
Next page
SATEL RE-4K 7
3. Click “Delete transmitter”. The “Confirm” window will be displayed.
4. Click “OK”. The "Confirm" window will be displayed.
5. Click “Write transmitters” to write the changes to the controller.
5.4 Restoring factory default settings and deleting keyfobs
When restoring the factory default settings, you can delete all keyfobs.
1. Press and hold down the PRG1 button.
2. After about 3 seconds, when the LED flashes red once, release the button.
3. Press and hold down again the PRG1 button.
4. After about 3 seconds, when the LED starts flashing red, release the button.
5. When the LED stops flashing red and turns on in green, it means that the factory default
settings of the controller have been restored.
5.5 Setting the operating mode for a relay output
You can set a different operating mode for each relay output. The output 1 pins are used as
an example in the table below.
Pulse mode [jumper across two pins on the right] – the relay output is turned
on when the keyfob button is pressed (up to 30 seconds – then the keyfob
stops transmitting to prevent the battery discharge).
Monostable mode [jumper across two pins on the left] – pressing the keyfob
button turns on the relay output for a preset time.
Bistable mode [jumper removed from pins] – each pressing the keyfob button
changes the relay output status to the opposite one.
5.6 Programming the relay output cut-off time
If the relay output works in the monostable mode, you can program the cut-off time for it
ranging from 1 to 255 seconds (by default: 5 seconds). The cut-off time is programmed
individually for each output.
Programming the time by using buttons
1. Press twice the controller button designated with the number of the relay output for which
you want to program the time. The LED will go off.
2. Press the keyfob button. The LED will start flashing green and red alternately.
3. Measure the time during which the relay output is to be turned on and press the keyfob
button again. The LED will turn on in green.
Programming the time by using the DLOAD10 program
1. Click “Read times” to read the times programmed in the controller.
2. In the “Time” column, enter the cut-off time for the given relay output.
3. Click “Write times” to write the changes to the controller.
6. Specifications
RE-4K controller
Supply voltage .........................................................................................................9...16 V DC
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel RE-4K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel RE-4K in the language / languages: English as an attachment in your email.

The manual is 0,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel RE-4K

Satel RE-4K User Manual - German - 11 pages

Satel RE-4K User Manual - Dutch - 11 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info