699886
1
Zoom out
Zoom in
Previous page
1/4
Next page
ASD-150
WIRELESS SMOKE DETECTOR
asd-150_en 02/17
The ASD-150 detector can detect the early stages of fire development when there is some visible smoke. It can
operate as a stand-alone device or as part of the ABAX two-way wireless system. This manual applies to the
detector with electronics version 1.1 and with firmware version 1.0, which is supported by:
ACU-120 / ACU-270 controller with firmware version 5.02 (or newer),
ARU-100 repeater with firmware version 2.02 (or newer),
INTEGRA 128-WRL control panel with firmware version 1.15 (or newer).
Rating plate of the device can be found on the enclosure base.
1. Features
EN 14604 compliant visible smoke sensor.
Detection of optical chamber fouling.
Red LED for optical signaling.
Built-in sounder.
Test feature.
Tamper switch (supervised when working in the ABAX system).
Battery status control.
2. Functional description
Smoke detection
An optical method is used for the detection of visible smoke. When the concentration of smoke in the optical
chamber exceeds a given threshold, an alarm is triggered. The detector automatically compensates for gradual
changes in the optical chamber caused by deposition of dust.
Alarm signaling
The alarm is indicated visually (LED steady light) and acoustically (intermittent sound) for 5 minutes. Pressing
the test / reset button (designated with the letter A in Figure 2) during the alarm will clear the alarm condition
and will block the smoke detection function in the detector for 5 minutes.
Operation as part of the ABAX system
Information about alarm is sent by radio to the ACU-120 / ACU-270 controller / INTEGRA 128-WRL control
panel. After the causes of alarm have ceased to exist, information about alarm end will be sent.
Note: The detector can signal alarm detected by another detector registered in the same controller or in the
same INTEGRA 128-WRL control panel. For detailed information about this option, please refer to the
ACU-120 / ACU-270 controller manual or the control panel manual.
After starting the test mode in the ABAX system, the LED indicates as follows:
polling – short flash (80 milliseconds). If the optical chamber is soiled – two short flashes.
alarm memory – flashing rapidly.
Note: The alarm memory is cleared after exiting the test mode.
3. Installation
The detector is designed for indoor operation. For typical home and/or office applications, the detectors should
be installed on the ceiling, at a distance of minimum 0.5 meter from the wall or other objects.
Do not install the detector in places with high concentration of dust and/or formation and
condensation of water steam. The detector should not be mounted in the vicinity of heaters and
cookers.
The detector enclosure can not be closed without the battery inserted.
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel ASD-150 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel ASD-150 in the language / languages: English as an attachment in your email.

The manual is 0,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel ASD-150

Satel ASD-150 User Manual - German - 4 pages

Satel ASD-150 User Manual - Dutch - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info