699871
3
Zoom out
Zoom in
Previous page
1/4
Next page
SATEL ACX-200 3
NO1...NO8 - relay output normally open contact.
Z1…Z4 - zone.
4. Installation
Disconnect power before making any electrical connections.
The device is designed for indoor installation. It is recommended that the expander be
mounted high above the floor. This will allow you to get a better range of radio
communication and avoid the risk of the expander being accidentally covered by
people moving around the premises.
1. Loosen the cover locking screws and remove the enclosure cover.
2. Connect the temporary 12 V DC power supply to the expander and add the device
to the wireless system (see the ACU-100 / ACU-250 / ACU-120 / ACU-270
controller manual or the INTEGRA 128-WRL / VERSA / VERSA Plus control panel
installer manual). The sticker with 7-digit serial number which shall be entered
when registering the expander in the system can be found on the electronics
board.
3. Fasten the expander temporarily at the place of its future installation.
4. Check the level of signal received from the expander by the ACU-100 / ACU-250 /
ACU-120 / ACU-270 controller or the INTEGRA 128-WRL control panel. If the
signal level is lower than 40%, select another place for installation. Sometimes, it
is sufficient to shift the device ten or twenty centimeters to obtain a considerable
improvement in the signal quality.
5. Having checked that the selected location of installation ensures the optimum
level of radio signal, disconnect the temporary 12 V DC power supply.
6. Place the enclosure base against the wall and mark location of the mounting
holes.
7. Drill the holes in the wall for wall plugs (screw anchors).
8. Make an opening for wire harness in the enclosure base.
9. Run the wires through the opening made (power wires, cables connecting wired
devices with the expander, etc.).
10. Using wall plugs (screw anchors) and screws, secure the enclosure base to the
wall.
11. Connect detectors to the expander zones. For the EOL configuration, use a 2.2 k
resistor, and for the 2EOL configuration – two 1.1 k resistors.
12. If the tamper switch is to be supervised, connect the tamper output terminals to
the expander zone (you can connect the tamper output in parallel with the detector
and configure the expander zone as 2EOL).
13. Connect the devices to the expander outputs.
Note: Given the specific character of radio communication, it is not recommended that
the expander be used in applications where quick switchover of the output
status is expected.
14. Connect 12 V DC power wires to the +12V and COM terminals.
15. Replace the cover and then lock it with the screw.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel ACX200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel ACX200 in the language / languages: English as an attachment in your email.

The manual is 0,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel ACX200

Satel ACX200 User Manual - German - 4 pages

Satel ACX200 User Manual - Dutch - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info