214390
42
Zoom out
Zoom in
Previous page
1/48
Next page
42
APPENDIX
TROUBLESHOOTING
Before calling your dealer or service center for assistance, check the matters below once again.
1. Make sure you have connected a projector to your computer or video equipment as described in the section
"CONNECTING PROJECTOR" on pages 11 ~ 13.
2. Check cable connection. Verify that all computer, video and power cord are properly connected.
3. Verify that all power is switched on.
4. If a projector still does not produce an image, re-start your computer.
5. If an image still does not appear, unplug a projector from your computer and check your computer monitor's display. The
problem may be with your graphics controller rather than with a projector. (When you reconnect a projector, be sure to
turn the computer and monitor off before you power up the projector. Power the equipment back on in order of : Projector
and computer.)
6. If the problem still exists, check the following chart.
No power.
Plug a projector into your AC outlet.
Make sure READY Indicator lights.
Wait 90 seconds after a projector is turned OFF when turning the projector back on.
NOTE : After pressing Power ON-OFF button to OFF, make sure a projector works as
follows:
1. LAMP indicator lights bright and READY indicator turns off.
2. After 90 seconds, READY indicator lights green again and a projector may be
turned on by pressing Power ON-OFF button.
Check WARNING TEMP. and READY indicator. If both WARNING TEMP. and READY
indicator flashes, the projector cannot be turned on.
(See "TURNING ON/OFF PROJECTOR" section on page 19.)
Check Projection Lamp. (Refer to page 38.)
Image is out of
focus.
Adjust focus of a projector.
Make sure a projection screen is at least 4.1 (1.2m) from the projector.
Check Projection Lens to see if it needs cleaning.
NOTE : Moving a projector from a cool temperature location to a warm temperature location
may result in moisture condensation on Projection Lens. In such an event, leave a
projector OFF and wait until condensation disappears.
Picture is Left/Right
reversed.
Check Ceiling / Rear feature. (See SETTING section on page 36.)
Problem: Try these Solutions
Picture is
Top/Bottom
reversed.
Check Ceiling feature. (See SETTING section on page 36.)
Some displays are
not seen during the
Operation.
Check Display feature.(See SETTING section on page 36.)
No image.
Check the connection between your computer or video equipment and a projector.
When turning a projector on, it takes about 30 seconds to display an image.
Check the system that you select is corresponding with your computer or video
equipment.
Make sure the temperature is not out of the Operating Temperature (5°C ~ 35°C).
No sound.
Check audio cable connection from audio input source.
Adjust the audio source.
Press VOLUME (+) button.
Press MUTE button.
42


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanyo plc xt16 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanyo plc xt16 in the language / languages: English as an attachment in your email.

The manual is 1,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info