569895
42
Zoom out
Zoom in
Previous page
1/44
Next page
REINIGEN DER PROJEKTIONSLINSE
Führen Sie folgende Schritte durch, wenn Sie die Linse reinigen wollen:
1.
Tragen Sie ein Reinigungsmittel, das speziell für Kameralinsen geeignet ist, in geringen Mengen auf ein weiches,
trockenes Tuch.
ACHTUNG: Ein scharfes oder mit Festkörpern durchsetztes Reinigungsmittel könnte die Linse verkratzen.
2. Wischen Sie vorsichtig über die Linse.
3. Stecken Sie die Schutzkappe auf das Objektiv, falls Sie den Projektor nicht anschließend nutzen wollen.
FEHLERSUCHE
Sollten Probleme mit Ihrem Projektor auftauchen, dann prüfen Sie bitte zunächst, ob Sie folgende Fragen mit JA
beantworten können:
1.
Wurde der Projektor, wie in den Kapiteln auf den Seiten 10 bis 14 beschrieben, angeschlossen ?
2. Sind alle Stecker fest mit den Buchsen verbunden?
3. Ist der Projektor und die Projektionslampe eingeschaltet?
4. Haben Sie den Computer gegebenenfalls neu gestartet?
5. Haben Sie geprüft, ob der Computermonitor nach dem Lösen der Verkabelung zum Projektor ein Bild anzeigt?
(Beachten Sie nach dem erneuten Anschließen zuerst den Projektor, dann den Computer und schließlich den Monitor
anzuschalten).
Sollte das Problem noch nicht behoben sein, sind in folgender Tabelle weitere Möglichkeiten der Fehlersuche
aufgeführt:
PROBLEM
Kein Strom
Das Bild ist verschwommen
MÖGLICHE LÖSUNG
l
Der Netzstecker ist nicht eingesteckt.
l
Der Hauptschalter ist nicht auf ON gelegt.
l
Die Projektionslampe ist nicht eingeschaltet.
l
Die PROJEKTIONSLAMPEN-EIN/AUS-Taste ist nicht
eingeschaltet.
l
Die Temparaturwarnlampe leuchtet, weil der Projektor überhitzt ist.
l
Die Projektionslampe ist defekt.
ANMERKUNG:
Nach dem Ausschalten der PROJEKTIONSLAMPEN-EIN/AUS-Taste
verhält sich der Projektor wie folgt.
1. Die Lampen-Netzanzeige leuchtet und die READY-Anzeige
erlischt.
2. Nach einer Minute leuchtet die READY-Anzeige wieder grün und
der Projektor kann wieder mit der
PROJEKTIONSLAMPEN-EIN/AUS-Taste eingeschaltet werden.
3. Der Lüfter bleibt noch etwa eine Minute in Betrieb
4. Nach einer Minute leuchtet die READY-Anzeige wieder grün und
die Projektionslampe kann wieder eingeschaltet werden.
l
Der Fokus muß angepaßt werden.
l
Der Projektionsabstand beträgt weniger als 1
,l
Meter.
l
Die Linse ist verschmutzt.
ANMERKUNG:
Durch starken
Temparaturwechsel,
z.B. durch Transport des
Projektors von einem kalten in einen warmen Raum, kann sich die
Linse beschlagen und die Bildqualität beeinträchtigen.
-
42
-
42


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanyo PLC 8815E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanyo PLC 8815E in the language / languages: German as an attachment in your email.

The manual is 4,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sanyo PLC 8815E

Sanyo PLC 8815E User Manual - English - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info