532744
6
Zoom out
Zoom in
Previous page
1/30
Next page
1
CAUTION
SANICONDENS
®
Plus is a pump for lifting condensation
water from an air conditioning system, a condensation boiler
or from refrigeration units. Include a neutralisation device if
necessary (see the manufacturer’s instructions for your boiler).
The pump starts automatically and has a high level of
performance, safety and reliability provided that all the
installation and maintenance instructions described in this
notice are strictly followed.
Please take particular note of the information marked by :
«
» Indication that a risk of electrical origin exists,
«
» Instructions for use only by qualified professionals.
OPERATING PRINCIPLE
SANICONDENS
®
Plus contains a pump. The tank of the
SANICONDENS
®
Plus is fitted with a float which controls the
operation of the motor. When the condensates enter the tank,
the pump starts up.
2
LIST OF DOCUMENTS PROVIDED:
see fig.2
3
DIMENSIONS:
see fig.3
4
SANICONDENS
®
Plus AREA OF APPLICATION AND
TECHNICAL DATA
Application
Air conditioning systems, boilers,
refrigeration units
Type CD10
Max. vertical pumping 4,5 m
Maximum flow rate (litres / hour) 342
Flow rate at 4 m 156
Min. pH 2,5
Voltage 220-240 V
Frequency 50 Hz
Power rating 60 W
Current consumption 0,52 A
Electrical class I
Protection index IP20
Sound level < 45 dBA
Average utilisation temperature 35°
Maximum allowable temperature 80°
S3 15% (90s ON, 510s OFF)
Net weight 2000 g
Dimensions 301x160x146 mm
Tank volume 2,1 litre
Supply cable 2 m
Discharge hose 6 m
Alarm cable (3 core) 2 m
Wall fastening Yes
CAUTION:
All applications other than those described in this notice are
prohibited.
5
PERFORMANCE CURVES:
see fig.5
6
VERTICAL PUMPING/HORIZONTAL PUMPING:
see fig.6
7
INSTALLATION
SANICONDENS
®
Plus has wall fixings.
The unit should be easy to access for testing and
maintenance.
The unit must be installed level. Adjust the installa-
tion using a spirit level before fixing the unit.
Make sure that the equipment is protected from damp while
installing it.
7a
CONNECTION AT THE COVER INLET
The unit has 4 inlets 28 mm in diameter (2 on each side - see
fig.
7a
1
). To connect the water to be drained off, connect
the water inlet to one of the inlets and close off any unused
inlets with the plugs
D
. If necessary, use the rubber adaptator
X
19, 32, 40 mm (see fig.
7a
2
).
7b
CONNECTING TO THE DISCHARGE PIPE
The SANICONDENS
®
Plus discharge pipe must be connected
to the flexible hose
A
(supplied : length 6 m). This hose should
be used to form the vertical section of the discharge pipe.

SANICONDENS
®
Plus (see diagram
7b
)
.

most vertical position
possible to avoid it kinking.

kinking.
The hose has a diameter of less than 8 mm and can be
connected to a PVC hose of larger diameter by a plastic
reducing connection on the horizontal section of the dis-
charge hose, or connected to your drain by a plastic redu-
cing connection
Y
. In UK fittings such as Speedfit from
John Guest are available -part numbers PEM202215W
used with PEM06150W to connect to 22mm pipework.
The SANICONDENS
®
Plus is fitted with a non-return valve
to prevent re-activation.
7c
ELECTRICAL CONNECTION
The electrical installation should be carried by a qualified person.
The unit should be connected to a fully earthed electrical
supply. All wiring must conform to BS7671, 1992 require-
ments for electrical installations. The SANICONDENS
®
Plus
requires a 220/240V single phase AC 50 Hz supply (UK
specification). Do not connect SANICONDENS
®
Plus to a
conventional plug and socket. It must be wired into a fused,
unswitched, fixed wiring connector fitted with a 5 amp fuse.
SANICONDENS
®
Plus has an Earth wire. The wires in the
mains lead are
coloured in accordance with the following code:
Brown – Live Blue – Neutral Green/Yellow – Earth
Warning: Ensure the electricity is turned OFF at the main
switch board before wiring to connector.
All work on cable, pressure chamber and motor should only
be carried out by a qualified Saniflo servicing agent, as
special tools are required.
7d
ALARM
SANICONDENS
®
Plus is fitted with a detection system
that can trigger an alarm if the water level rises too high
(audible or visual alarm, 1.5V to 230V), see diagram
7d
:
1
. Brown wire: shared wire
2
. Black wire: normally off
3
. Blue wire: normally on
To fit the alarm, connect the blue and brown wires
of the alarm to the respective terminals on the
SANICONDENS
®
Plus.
UK
INSTRUCTIONS INTENDED SOLELY FOR
QUALIFIED PROFESSIONALS
INSTRUCTIONS INTENDED SOLELY FOR
QUALIFIED PROFESSIONALS
10721 140 SANICONDENS PLUS.indd 6 23/10/12 14:17
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanibroyeur SANICONDENS Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanibroyeur SANICONDENS Plus in the language / languages: All languages as an attachment in your email.

The manual is 5,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info