797018
10
Zoom out
Zoom in
Previous page
1/12
Next page
09
GB
F
E
4. To cancel the Sleep Timer function before the preset
time has elapsed, simply press and release the Standby
(main power) button to turn the unit off manually.
Display & Audio setup
Dimmer control
The brightness of the display may be adjusted. If you use
the unit in the bedroom, you may prefer a lower brightness
level than the standard setting.
1. Press and release the Snooze / Dimmer button repeatedly
to adjust the brightness level of the LCD display. The
backlight level will change with 8 different illumination
levels, you’ll be able to see the effect of the change.
2. Stop when the desired backlight level is reached.
Tone control
You can adjust the bass and treble of the sound of your
RCR-30 to enhance the tone while listening.
1. First ensure your radio is switched on. Press and
release the Volume control button to enter the tone
control setting.
2. The bass value will appear on the display. Rotate the
Volume control knob to adjust between +5~-5, and
press and release the Volume control button to confirm
the setting.
3. Then the treble value will appear on the display. Rotate
the Volume control knob to adjust between +5~-5, and
press and release the Volume control button to confirm
the setting.
4. You can also press the Bass up / down button and
Treble up / down button on the Remote control to
adjust the bass and treble of the sound.
Loudness
You can get compensation on lower and higher frequency
for your RCR-30 by adjusting the Loudness function.
1. Press and hold the Info / Menu button to enter the
menu setting.
2. Rotate the Tuning control knob until LOUD ON / OFF
appears on the display. Press and release the Tuning
control button to enter the setting.
3. Rotate the Tuning control knob to choose ON to turn
on the Loudness function, then press and release the
Tuning control button to confirm the setting.
4. To turn off the Loudness function, select OFF and
press and release the Tuning control button to confirm
the setting.
Mute function
Press the Mute button on the remote control of your radio,
it will mute the output from the loudspeakers.
1. Press the Mute button to mute the sound output.
2. Press the Mute button again or one of the Volume
buttons to un-mute the sound output.
Auxiliary input socket
A 3.5mm stereo Auxiliary Input socket is provided on the
rear of your radio to permit an audio signal to be fed into
the unit from an external audio device such as iPod, MP3
or CD player.
1. Press the Standby (main power) button to switch on
your radio.
2. Repeatedly press and release the Source button until
AUX IN is displayed.
3. Connect an external audio source (for example, iPod,
MP3 or CD player) to the Auxiliary Input socket.
4. Adjust the volume setting on your iPod, MP3 or CD
player to ensure an adequate signal level from the
player, and then use the Volume control on the radio as
needed for comfortable listening.
Headphone socket
A 3.5mm Stereo Headphone output socket located on the
rear of your radio is provided for use with headphones.
Inserting headphones will automatically mute the internal
loudspeaker. Please be aware that the sensitivity of
headphones can vary widely. We therefore recommend
setting the volume to a low level before connecting
headphones to the radio.
Excessive sound pressure from earphones
and headphones can cause hearing loss.
To prevent possible hearing damage, do not
listen at high volume levels for long periods.
IMPORTANT
Software version / Setting tuning step /
FM range setting
Software version
The software version display cannot be altered and is just
for your reference.
1. Turn off the radio.
2. Press and hold the Source button until you hear a beep
and the software version (e.g. VER XXX) is shown on
the display.
Setting tuning step
1. After the software version is shown on the display,
rotate the Tuning control knob until FM xkHz or AM
xkHz appears on the display, and press the Tuning
control button to enter FM or AM step setting. The
“xkHz” will flash on the display.
2. Rotate the Tuning control knob to select 50kHz / 100kHz
for FM radio, and 9kHz / 10kHz for AM radio. Then press
the Tuning control button to confirm the setting.
The tuning steps for North America are FM: 100kHz
and AM: 10kHz
The rest of the world is FM: 50kHz and AM: 9kHz
NOTE
Change in the AM tuning step setting will result in the
removal of all AM presets stored in the radio, this is not
the case for your FM tuning steps.
NOTE
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sangean RCR-30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sangean RCR-30 in the language / languages: English as an attachment in your email.

The manual is 2.77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info