797034
17
Zoom out
Zoom in
Previous page
1/19
Next page
16
GB
F
E
NL
D
using the signal (see chapter 6 "USING THE MENU" for
more information). The RDS CT feature is a convenient
feature that enables you to always have the correct time
set when tuning in to an FM station that broadcasts an
RDS CT signal.
NOTE
Not all stations broadcast the CT and many are not
always accurate, this is the fault the broadcast signal
not the radio.
When tuned to an FM station with RDS, additional
information that is being broadcasted can be shown in the
Text display (U) by repeatedly pressing the Info button (29).
The radio will show the following information in sequence:
1. Preset name - Displays the name of the
preset.
2. Program service name - Displays the name that is
broadcasted by the radio
station.
3. Program Type - Displays the type of program
that is being received.
4. Radio Text - Displays text message that
is broadcasted by the radio
station.
5. Signal strength - Displays the signal strength.
6. Signal-noise ratio - Displays the signal to noise
ratio.
7. Memory bank A / B / C - Displays the memory bank
that is currently being used.
The available layers of information and the information
that is displayed are also shown in the table below:
Layer FM with RDS or RBDS
1 Preset name
2 RDS / RBDS PS
3 RDS / RBDS PTY
4 RDS / RBDS RT
5 RSSI -- xxDB
6 SNR -- xxDB
7 MEMOBANK - A / B / C
Note: RSSI: Radio Signal Strength Indication
SNR: Signal to Noise Ratio
RDS: Radio Data System for Europe area
RBDS: Radio Broadcast Data System
USING THE RADIO TO CHARGE
BATTERIES
The ATS-909X2 can be used to charge rechargeable NI-
MH or NI-CAD batteries when the radio is powered off.
Before charging batteries using the ATS-909X2, please
first make sure that the batteries that are being used are
rechargeable NI-MH or NI-CAD batteries.
Then follow these steps to charge the batteries:
1. Open the Battery Compartment cover (43) in the
direction indicated by the arrow on the cover.
2. Insert 4 x NI-MH or NI-CAD (AA Size) batteries into the
Battery Compartment (43) with polarities as shown on
the diagram on the cover and inside the compartment.
3. Place the Battery switch (47) in the NIMH / NICAD
(Charger) position.
4. Close the Battery Compartment (43) again.
5. Make sure the radio is turned off to charge the batteries.
The Charge indicator (9) will blink in red when the
batteries are being charged.
6. When the batteries are fully charged, the Text display
(U) will show the message "BATT FULL".
NOTE
If any abnormalities are detected while charging
batteries, the Text display (U) will show the message
"BT-X-CHECK", where "X" represents the number of
the battery that needs to be checked and / or replaced
(e.g. "BT-1-CHECK" means that battery 1 needs to be
checked and / or replaced). Which battery corresponds
to which battery number is shown both on the battery
compartment cover (43) and inside the battery
compartment (43).
SETTING THE DISPLAY BRIGHTNESS
LEVEL
The Backlight button (11) can be used to illuminate the
display or to set the brightness level of the display. Press
the Backlight button (11) repeatedly to select the desired
brightness level or to illuminate the display when the
backlight has turned off.
CHECKING THE SOFTWARE VERSION
The radio's software version can be shown both in the
menu and by performing these steps:
1. Make sure the radio is powered off.
2. Press the Enter button (30), the radio shows the
software version on its display.
The version display cannot be altered and is just for
your reference.
USING THE TONE CONTROL SWITCH
The Tone Control switch (14) at the right side of the radio
allows you to adjust the tone of the radio based on the
broadcasted programs. The switch has three settings:
Music, Normal and News.
NOTE
This switch can also be used to reduce noise on the AM
/ USB / LSB bands by placing it in the News position.
This can enhance the voice quality as well.
USING THE LOCK SWITCH
The Lock switch (15) can be used to prevent unintentional
operation of the radio. This can come in handy to prevent
the radio from being turned on when it is being transported
or to prevent the radio from accidentally being powered off.
When the Lock switch (15) is placed in the ON position,
the radio will not respond to any user input and the Button
Lock indicator (A) will be shown on the radio's display. To
unlock the radio, place the switch in the OFF position. The
Button Lock indicator (A) will now no longer be shown and
the radio can be operated again using its buttons.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sangean ATS-909X2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sangean ATS-909X2 in the language / languages: English as an attachment in your email.

The manual is 2.39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sangean ATS-909X2

Sangean ATS-909X2 User Manual - German - 20 pages

Sangean ATS-909X2 User Manual - Dutch - 21 pages

Sangean ATS-909X2 User Manual - French - 21 pages

Sangean ATS-909X2 User Manual - Spanish - 21 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info