Zoom out
Zoom in
Previous page
1/93
Next page
SP-M206 SP-M226 SP-M256 SP-M275 SP-M305
LCD Projector
Owner’s Instructions
The color and the appearance of the product may differ
from the illustrations in this manual. The specifications are
subject to change without prior notice to improve
performance.
1


Need help? Post your question in this forum.

Forumrules


Content of pages


  • Page 1

    SP-M206 SP-M226 SP-M256 SP-M275 SP-M305LCD ProjectorOwners InstructionsThe color and the appearance of the product may differfrom the illustrations in this manual. The specifications aresubject to change without prior notice to improveperformance. ...
  • Page 2

    Table Of ContentsMAJOR SAFETY PRECAUTIONSBefore You Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3INSTALLATION AND CONNECTIONPackage Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1Installing the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2Leveling with Adjustable Feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3Zoom and Focus Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4Screen Size and Projection Distance. . . . . . . . . . . . . . . . . . . . . . . . . 2-5Lamp Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6Rear Side . . . . . . . . . . . . . . ...
  • Page 3

    MORE INFORMATIONSpecifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1RS232C Command Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2Contact SAMSUNG WORLDWIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3Correct Disposal - Europe only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 ...
  • Page 4

    1Major Safety Precautions1-1Before You StartIcons used in this manualICONNAMEMEANINGCautionIndicates cases where the function may not work or the setting may be canceled.NoteIndicates a hint or tip to operate a function.Using this ManualMake yourself fully aware of the safety precautions before using this product.The contents of this manual are subject to change without prior notice for performance improvement.If a problem occurs, refer to the 'Troubleshooting' section.Copyright NoticeCopyright 2010 Samsung Electronics Co., Ltd. All rights reserved.The copyright of this manual is reserved by Samsung Electronics, Co., Ltd.The contents of this manual may not be partially or in whole reproduced, distributed or used in any form without the writtenpermission of Samsung Electronics, Co., Ltd.An administration fee may be charged if either.(a) An engineer is called out at your request and there is no defect in the product.(i.e. where you have failed to read this user manual).(b) You bring the ...
  • Page 5

    1-2Care and MaintenanceCleaning the Surface and the LensClean the projector using a soft dry cloth.Avoid cleaning the product with a flammable substance such asbenzene or thinner.Avoid scratching the lens with your fingernails or a sharp object.This may result in scratches or damage to the product.Avoid cleaning the product with a wet cloth or by directlyspraying water onto the product.If water enters the product, it may result in fire, electric shock, ora problem with the product.A white stain may appear on the surface of the projector if watergets on it.The appearance and the color may differ depending on themodel.Cleaning Inside the ProjectorFor cleaning the interior of the projector, contact an authorizedSamsung Service Center.1-2Contact a Service Center if dust or other substances are insidethe projector.Major Safety Precautions ...
  • Page 6

    1-3Safety PrecautionsIcons used for safety precautionsICONNAMEMEANINGWarningFailing to follow the precautions marked with this sign may result in a serious injury or evena fatality.CautionFailing to follow the precautions marked with this sign may result in a personal injury orproperty damage.Meaning of SignsDo not perform.Must be followed.Do not disassemble.The power plug must be unplugged from thewall outlet.Do not touch.Must be grounded to prevent electric shock.Power RelatedThe following images are for your reference and may differ depending on models and countries.The appearance and the color may differ depending on models.WarningPlug the power plug in firmly.Otherwise, it may result in fire.Avoid connecting multiple electric appliances to a single wall outlet.Avoid using a damaged power cord or plugor a loose power outlet.Otherwise, it may result in electricshock or fire.Avoid plugging in or unplugging the powersupply with wet hands.Otherwise, it may result in electricshock.Major ...
  • Page 7

    Make sure to connect the power cord to agrounded wall outlet (for insulation class 1equipment only).Otherwise, it may result in electricshock or injury.CautionWhen unplugging the power plug from thewall outlet, make sure to hold the powerplug by the plug and not by the cord.Failing to do so may result in electricshock or fire.Unplug the power plug before cleaning theproduct.Do not turn the product on or off by plugging or unplugging the power plug. (Do notuse the power plug as a power switch.)Keep the power cord away from sources ofheat.There is a danger of electric shock orfire.Connect the power plug to a wall outletthat can be easily reached.When a problem occurs with theproduct, you must unplug the powerplug to cut the power off completely.You cannot cut the power offcompletely using only the power buttonon the product.Installation RelatedWarningAvoid installing the product in a locationexposed to direct sunlight and installingthe product near a heat source such as afire or heater.1 ...
  • Page 8

    Do not install the product in a locationexposed to dust, moisture (sauna), oil,Do not install the product in areas withheavy dust.smoke or water (rain drops) and do notinstall it in a vehicle.This may result in electric shock or fire.CautionTake care not to block the vent with a tablecloth or curtain.Do not let the product drop while moving it.Otherwise, it may result in fire due tointernal overheating.This may result in a problem with theproduct or injury.When putting the product down, place itgently.Do not install the product at a height wherechildren may reach it.Failing to do so may result in a problemwith the product or injury.If a child touches the product, theproduct may fall and this may result ininjury.Usage RelatedAvoid inserting metal objects such aschopsticks, coins or hairpins, or inflammable objects into the product (the vents,ports, etc).If water or an alien substance entersthe product, turn the power off, unplugthe power cord and contact a servicecenter.Otherwise, it ma ...
  • Page 9

    CautionIf the product generates a strange noise, aburning smell, or smoke, unplug the powerplug immediately and contact a servicecenter.Failing to do so may result in electricshock or fire.If the power plug pin or jack is exposed todust, water or alien substances, clean itthoroughly.Do not use the product while it indicates amalfunction, such as no sound or no picture.There is a danger of electric shock orfire.Turn the product off immediately,unplug the power cord from a walloutlet, and contact a Service Center.When cleaning the product, disconnect thepower cord and clean the product with asoft dry cloth.When a gas leak occurs, do not touch theproduct or the power plug and ventilateimmediately.A spark may result in an explosion orfire.During a thunder or lighting storm, donot touch the power cord or antennacableAvoid using chemicals such as wax,benzene, alcohol, thinner, mosquitorepellent, fragrance, lubrication orcleansing agent when cleaning theproduct.This may result in the exterior ...
  • Page 10

    To avoid burning yourself, do not touch thevents or lamp cover while operating orright after turning off the product.Do not clean the product using water sprayor a wet cloth. Avoid using any chemicalssuch as detergents, industrial or automotive polish, abrasive, wax, benzene, alcohol on any plastic part of the product suchas projector case, since this may causedamage.Do not open any cover on the product.Do not use any undesignated battery.This would prove hazardous becauseof high-voltage current inside theproduct.Be careful not to touch the ventilation holewhile the projector is on as hot air comesout.The ventilation hole is hot for some timethough the projector is turned off. Keepyou hands or body off the ventilation hole.Do not place objects vulnerable to heatnear the projector.Be careful to keep your body away fromthe projector lamp. The lamp is hot.(Children and those who have sensitiveskin should be more careful.)Take care not to lose the lens cover of theproduct.The lens could ge ...
  • Page 11

    2Installation and Connection2-1Package ContentsUnpack the product and check if all of the contents listed below have been included.Store the packaging box in case you need to move the product at a later date.ProjectorCONTENTSQuick Setup GuideWarranty Card (Not availablein all locations)User ManualPower CordRemote Control / 2 BatteryCleaning ClothD-Sub CableLens cover( Not available in all locations)4 ScrewsProjector case(For ceiling mount bracket.)A ceiling mount is not included and must be purchased separately. Use the included screws to attach the projector tothe ceiling mount bracket.2-1Installation and Connection ...
  • Page 12

    2-2Installing the ProjectorInstall the projector so that the beam from the projector is perpendicular to the screen.Place the projector so that the lens aims at the center of the screen. If the screen is not vertical, the picture on thescreen may not appear rectangular.Do not install the screen in bright surroundings. If the surroundings are too bright, the picture on the screen will bewashed out and not display clearly.When using the projector in bright surroundings, use curtains to block the light.You can install the projector in the following locations relative to the screen : <Front-Floor> / <Front-Ceiling> / <RearFloor> / <Rear-Ceiling>. To view the installation position settings, see below.To adjust the picture when you install the projector behind the screenInstalling behind a semi-transparent screen.When you install the projector behind a semi-transparent screen,you can use the menu to adjust the picture so that it displays correctly, depending on where you've located the proje ...
  • Page 13

    2-3Leveling with Adjustable FeetPress the PUSH buttons, as shown, to adjust the legs and levelthe projector.The projector can be adjusted to a height of up to 1.18 inches (30mm, about 12 ) from the reference point.If <Auto Keystone> is set to <On>, <V-Keystone> is adjusted automatically.If fine tuning is required after auto-adjustment, use <V-Keystone>.2-3Installation and Connection ...
  • Page 14

    2-4Zoom and Focus AdjustmentZoom KnobYou can adjust the size of the image within the zoom rangeby manipulating the Zoom Knob.Focus RingFocus the picture on the screen using the Focus Ring.The size of your screen determines the distance you set your projector from the screen.If you do not install your projector at the projection distance specified in the Screen Size and Projection Distance table inSection 2-5, you will not be able to adjust the focus correctly.Installation and Connection2-4 ...
  • Page 15

    2-5Screen Size and Projection DistanceA. Screen / Z. Throw Distance / Y. Distance from Lens Center to Image BottomInstall the projector on a flat, even surface and level the projector using the adjustable feet to obtain optimal picture quality.If images are not clear, adjust them using the Zoom Knob or Focus Ring, or move the projector forward and backward.SCREEN SIZEM (DIAGONAL)X (HORIZONTAL)THROW DISTANCEY (VERTICAL)Z (TELE)OFFSETZ (WIDE)Y'INCHESCMINCHESCMINCHESCMINCHESCMINCHESCMINCHESCM3076.22460.91845.742.7108.435.590.12.66.340101.63281.32461.057.0144.747.4120.33.38.450127.040101.63076.271.2180.859.2150.44.110.560152.448121.93691.485.4217.071.0180.45.012.670177.856142.242106.799.7253.182.9210.55.814.780203.264162.648121.9113.9289.494.7240.66.616.890228.672182.954137.2128.2325.6106.6270.77.418.9100254.080203.260152.4142.4361.7118.4300.78.321.0110279.488223.566167.6156.6397.8130.2330.89.123.1120304.896243.872182.9170.9434.0142.1360.89.925.2130330.2104264.278198.1185.1470.3153.9391.01 ...
  • Page 16

    SCREEN SIZEM (DIAGONAL)X (HORIZONTAL)THROW DISTANCEY (VERTICAL)Z (TELE)OFFSETZ (WIDE)Y'INCHESCMINCHESCMINCHESCMINCHESCMINCHESCMINCHESCM240609.6192487.7144365.8341.8868.1284.2721.819.950.4250635.0200508.0150381.0356.0904.2296.0751.820.752.5260660.4208528.3156396.2370.2940.4307.8781.921.554.6270685.8216548.6162411.5384.5976.5319.7811.922.356.7280711.2224569.0168426.7398.71012.8331.5842.123.258.8290736.6232589.3174442.0413.01049.0343.4872.224.060.9300762.0240609.6180457.2427.21085.1355.2902.224.863.0310787.4248629.9186472.4441.41121.2367.0932.325.665.1320812.8256650.2192487.6455.71157.4378.9962.326.567.2330838.2264670.5198502.8469.91193.5390.7992.327.369.3340863.6272690.8204518.0484.21229.6402.61022.428.171.4350889.0280711.1210533.2498.41265.8414.41052.429.073.5360914.4288731.4216548.4512.61301.9426.21082.529.875.6370939.8296751.7222563.6526.91338.0438.11112.530.677.7380965.2304772.0228578.8541.11374.2449.91142.631.479.8390990.6312792.3234594.0555.41410.3461.81172.632.381.94001016.0320812 ...
  • Page 17

    2-6Lamp ReplacementCautions on Lamp ReplacementThe projector lamp is an expendable item. For best operating performance, replace the lamp according to the usage time.You can view the lamp usage time in the Information Display (INFO button).Replace the lamp with the one specified below only.ModelSP-M206 / SP-M226SP-M256 / SP-M275 / SP-M305Lamp Model NameDPL3311UDPL3321U- For inquiries on lamp purchase, please see 'Contact SAMSUNG WORLDWIDE' in section 6-3.Check that the power cord is unplugged before replacing the lamp.Because the lamp is a high temperature and high voltage product, wait at least one hour from the time you disconnect thepower cord before replacing the lamp.The projector lamp is on the top of the projector.Do not leave the old lamp near flammable items or in reach of children. There is a danger of fire, burns, or injury.Remove dirt or foreign material around or inside the lamp unit using a proper vacuum device.When handling the lamp, avoid touching any part of it except ...
  • Page 18

    Install a new lamp in the reverse order of removal.Replacing and Cleaning the FilterPrecautions when replacing the projector filter:The filter is on the side of the projector.Turn off the power of the projector, and then disconnect the power cord after the projector has cooled sufficiently.Otherwise, its parts may be damaged due to internal heat.When you replace the filter, you may release some dust.For inquiries on replacement filter purchase, please see 'Contact SAMSUNG WORLDWIDE' in Chapter 6.To replace or clean the filter, follow these steps:1. Turn off the power of the projector, and then disconnect the power cord after the projector has cooled sufficiently.2. Open the filter cover.3. Replace or clean the filter.When cleaning the filter, use a small vacuum cleaner designed for computers and small electronics products, or wash it underrunning water.After washing the filter under running water, make sure to dry it completely. The moisture may cause the filter to corrode.If dust cann ...
  • Page 19

    Air outtake ventAir intake vent2-6Installation and Connection ...
  • Page 20

    2-7Rear SideICONNAMEKensington Lock slotPC IN portVIDEO IN portAUDIO IN (L-AUDIO-R) portHDMI/DVI IN portRemote Control Signal ReceiverPower Input portAUDIO OUT/portRS232C portLAN portUSB portInstallation and Connection2-7 ...
  • Page 21

    2-8Supported Display Modes2-8-1. PC Timing (D-Sub/HDMI)FORMAT2-8RESOLUTIONHORIZONTALFREQUENCY(KHZ)VERTICALFREQUENCY(HZ)PIXELFREQUENCY(MHZ)IBM640 x 35070Hz31.46970.08625.175IBM640 x 48060Hz31.46959.94025.175IBM720 x 40070Hz31.46970.08728.322MAC640 x 48067Hz35.00066.66730.240VESA640 x 48070Hz35.00070.00028.560VESA640 x 48072Hz37.86172.80931.500VESA640 x 48075Hz37.50075.00031.500VESA720 x 57660Hz35.91059.95032.750VESA800 x 60056Hz35.15656.25036.000VESA800 x 60060Hz37.87960.31740.000VESA800 x 60070Hz43.75070.00045.500VESA800 x 60072Hz48.07772.18850.000VESA800 x 60075Hz46.87575.00049.500MAC832 x 62475Hz49.72674.55157.284VESA1024 x 76860Hz48.36360.00465.000VESA1024 x 76870Hz56.47670.06975.000VESA1024 x 76872Hz57.67272.00078.434VESA1024 x 76875Hz60.02375.02978.750VESA1152 x 86460Hz53.78359.95981.750VESA1152 x 86470Hz63.00070.00096.768VESA1152 x 86472Hz64.87272.00099.643VESA1152 x 86475Hz67.50075.000108.000MAC1152 X 87075Hz68.68175.062100.000VESA1280 x 72060Hz44.77259.85574.500VESA1280 x 72070 ...
  • Page 22

    FORMATRESOLUTIONHORIZONTALFREQUENCY(KHZ)VERTICALFREQUENCY(HZ)PIXELFREQUENCY(MHZ)VESA1280 x 96072Hz72.07272.000124.540VESA1280 x 96075Hz75.23174.857130.000VESA1280 x 102460Hz63.98160.020108.000VESA1280 x 102470Hz74.62070.000128.943VESA1280 x 102472Hz76.82472.000132.752VESA1280 x 102475Hz79.97675.025135.000VESA1440 x 90060Hz55.93559.887106.500VESA1440 x 90075Hz70.63574.984136.750VESA1600 x 120060Hz75.00060.000162.000VESA1680 x 1050 RB60Hz64.67459.883119.000VESA1680 x 105060Hz65.29059.954146.250VESA1920 x 1080 RB60Hz66.58759.934138.500VESA1920 x 1200 RB60Hz74.03859.950154.000All resolutions higher or lower than 1024x768 are converted to 1024x768 by the Scaler chip inside the projector. If theresolution of the signal output by the PC matches the real resolution (1024x768) of the projector, the screen quality isoptimal.2-8-2. AV Timing (D-Sub)FORMATRESOLUTIONSCANBT.601 SMPTE 267M480i59.94HzInterlacedBT.1358 SMPTE 293M480p59.94HzProgressiveBT.601576i50HzInterlacedBT.1358576p50HzProgressiveSM ...
  • Page 23

    FORMATRESOLUTIONSCANHORIZONTALFREQUENCY(KHZ)VERTICALFREQUENCY(HZ)PIXELFREQUENCY(MHZ)EIA-861Format2,3720 x 480Progressive31.46959.94027.000EIA-861Format2,3720 x 480Progressive31.50060.00027.027EIA-861Format41280 x 720Progressive44.95559.93974.175EIA-861Format41280 x 720Progressive45.00060.00074.250EIA-861Format51920 x 1080Interlaced33.71659.93974.175EIA-861Format51920 x 1080Interlaced33.75060.00074.250EIA-861Format161920 x 1080Progressive67.50060.000148.500EIA-861Format17,18720 x 576Progressive31.25050.00027.000EIA-861Format191280 x 720Progressive37.50050.00074.250EIA-861Format201920 x 1080Interlaced28.12550.00074.2502-8-4. AV Timing (VIDEO)NTSC, NTSC 4.43, PAL, PAL60, PAL-N, PAL-M, SECAMYour projector supports the standard video formats listed above through its video inputs. No adjustments arenecessary.2-8Installation and Connection ...
  • Page 24

    2-9Connecting the Power1. Plug the power cord into the power terminal on the rear side of the projector.Installation and Connection2-9 ...
  • Page 25

    2-10 Connecting with a PC and Setting up the PC2-10-1. Setting up the PC EnvironmentCheck the following items before connecting your PC to your projector.1. Click the right mouse button on the Windows desktop, and then click [Properties].The <Display Properties> dialog appears.2. Click the [Settings] tab, and then set the <Screen resolution>. The optimal resolution for the projector is 1024 x 768. For otherresolutions supported by the projector, see the PC Timing Display Mode table in section 2-8.You do not have to change the <Color quality> setup.3. Press the [Advanced] button. Another property window appears.4. Click the [Monitor] tab and set the <Screen refresh rate>. For the refresh rate that matches the resolution youve chosen, seethe refresh rate (60 Hz, 70 Hz, etc.) next to your selected resolution in the PC Timing Display Mode table in section 2-8.Setting the refresh rate sets both the vertical and horizontal frequencies.2-10Installation and Connection ...
  • Page 26

    5. Click the [OK] button to close the window, and then click the [OK] button on the <Display Properties> window to close thatwindow.6. Shut down the PC and connect it to the projector.The setup process might vary depending on your type of computer or version of Windows.(For example, [Properties] appears instead of [Properties (R)] as shown in 1.)This projector supports 32 bit color quality (per pixel) when it is used as a PC monitor.Projected images may differ from the images on your monitor depending on the monitor manufacturer or Windows version.When connecting the projector to a PC, make sure that the PC setup complies with the display settings supported by thisprojector. If it does not, you may have signal problems.2-10-2. Connecting with a PCMake sure that your PC and projector are turned off.1. Connect the [PC IN] port on the rear side of the projector to the PC video out (D-sub) port of the PC using a PC video cable.2. Plug in the power cords of the projector and the PC.This pro ...
  • Page 27

    2-11 Connecting a PC using an HDMI/DVI cable2-11-1. Connecting a PC using an HDMI/DVI cableMake sure that your PC and projector are turned off.1. Connect the [HDMI/DVI IN] terminal of the projector to the HDMI or DVI terminal of your PC using a HDMI/HDMI or HDMI/DVIcable (Not supplied).- If you are connecting to the HDMI terminal of your PC, use an HDMI/HDMI cable (Not supplied).- For the supported resolutions and refresh rates, see PC Timing (D-Sub/HDMI) in Section 2-8, "Supported Display Modes".2-11-2. Configuring the Audio Settings for Your PCWhen the projector is connected to the PC via an HDMI cable, you can change the audio settings as follows:1. In Category View of Windows XP : Go to Control Panel - [Sounds, Speech and Audio Devices], and select <SpeakerSettings>.2-11Installation and Connection ...
  • Page 28

    In Classic View of Windows XP : Go to Control Panel - [Sound and Audio Devices], and select the <Audio> tab.On Windows 7 : Go to Control Panel - [Sound], and select the <Playback> tab.2. Specify the default device for sound playback:You can select the PC speakers or projector speaker.The aforementioned information may slightly differ from some PCs or versions of Windows.Installation and Connection2-11 ...
  • Page 29

    2-12 Connecting an HDMI-Compatible DeviceMake sure that the AV device and your projector are turned off.1. Connect the [HDMI/DVI IN] terminal at the back of the projector to the HDMI or HDMI/DVI output terminal of the digital outputdevice using an HDMI/DVI or HDMI/HDMI cable.- If you are connecting to the HDMI output terminal on the digital output device, use an HDMI/HDMI cable.- For supported input signal formats, resolutions, and frequencies, see AV Timing(HDMI) in Section 2-8, "Supported DisplayModes".2. If you connected using a HDMI/DVI cable, connect the [AUDIO IN (L-AUDIO-R)] terminal on the projector to the Audio outterminal on your digital output device using an audio cable (Not supplied).- If you connected with a HDMI/HDMI cable, you do not need an audio cable.2-12Installation and Connection ...
  • Page 30

    2-13 Connecting an AV device using a D-Sub cableMake sure that the AV device and your projector are turned off.1. Connect the [PC IN] terminal at the back of the projector to the D-Sub terminal of your AV device using a D-Sub cable.- For supported input signal formats, resolutions, and frequencies, see AV Timing (D-Sub) in Section 2-8, "Supported DisplayModes".2. Connect the [AUDIO IN (L-AUDIO-R)] terminal at the back of the projector to the Audio out terminal of your AV device using anaudio cable (Not supplied).Installation and Connection2-13 ...
  • Page 31

    2-14 Connecting an AV device with Component outputMake sure that the AV device and your projector are turned off.1. Connect the [PC IN] terminal on the back of the projector to the Component terminal on your AV device using a D-Sub toComponent cable (Not supplied). This cable has a D-Sub connector on one end and three RCA jacks on the other.- For supported input signal formats, resolutions, and frequencies, see AV Timing (D-Sub) in Section 2-8, "Supported DisplayModes".2. Connect the [AUDIO IN (L-AUDIO-R)] terminal on the back of the projector and the Audio out terminal on your AV device usingan audio cable (Not supplied).2-14Installation and Connection ...
  • Page 32

    2-15 Connecting using a Video cableMake sure that the AV device and your projector are turned off.1. Connect the AV device to the [VIDEO IN] port using a VIDEO cable (not supplied).- For supported input signal formats, see AV Timing (VIDEO) in section 2-8, "Supported Display Modes".2. Connect the [AUDIO IN (L-AUDIO-R)] terminal on the back of the projector and the Audio out terminal on your AV deviceusing an audio cable (Not supplied).Installation and Connection2-15 ...
  • Page 33

    2-16 Connecting an External SpeakerYou can hear sound through an external speaker instead of the internal speakers built into the projector.1. Obtain an audio cable (Not supplied) suitable for your external speaker.2. Connect the [AUDIO OUT/ ] terminal of the projector to the external speaker using an audio cable.- When using an external speaker, the internal speaker does not operate but you can adjust the volume of the externalspeaker using the Volume button or the remote control of the projector.- The [AUDIO OUT/2-16] terminal can output all audio signals.Installation and Connection ...
  • Page 34

    2-17 Connecting to a NetworkThis product can use network functions. Refer to the following Network connection method.2-17-1. Connecting to a Dynamic IP (DHCP) NetworkYou can attach the projector to your network through a modem that uses DHCP (Dynamic Host Configuration Protocol). Whenyou use a DHCP modem, the modem automatically provides the IP address, subnet mask, and gateway values that the projectorneeds to access the network.To connect to a DHCP network, follow these steps :1. Connect the modem cable between the modem port on the wall and the external modem.2. Connect a LAN cable between the external modem and the wired or wireless IP router.3. Connect a LAN cable between the [LAN] port on the back of the projector and the wired or wireless IP router.4. Turn the projector on and press the [MENU] button.5. Select <Setup> <Network> <IP Setting> <Automatic>.6. The projector automatically acquires the IP address, Subnet mask and Gateway.To use the network function, <Network> must b ...
  • Page 35

    2-17-2. Connecting to a Static IP NetworkYou can attach the projector to a network that uses a Static IP address, which corresponds to using a dedicated lease line. If yournetwork uses Static IP addresses, you must get the IP address, subnet mask, and gateway values from your Internet ServiceProvider (ISP), turn on the Network function in the projector's Menu, and then enter the values into the Network functionmanually.To connect to a Static IP address network, follow these steps :1. Connect a LAN cable between the LAN port on the wall and a wired or wireless IP router.2. Connect a LAN cable between the [LAN] port on the back of the projector and the wired or wireless IP router.3. Turn on the projector, and then press the [MENU] button.4. Select <Setup> <Network> <IP Setting> <Manual>.5. Select <IP Address> and press the [/ buttons to enter values.] button. Use the/buttons to navigate between each IP Address entry field and the6. When done entering all the values for IP Address, pre ...
  • Page 36

    2-18 Kensington Lock slotThe Kensington Lock slot allows you to lock your projector, providing a sense of security when you use it in a public place.Because the shape and usage of the lock may differ depending on the model and the manufacturer, see the User Manualsupplied with the locking device for more information.Locking the product1. Loop the Kensington lock cable around an immovable part of desk or heavy object as directed in the Kensington lock usermanual.2. Insert the locking part of the locking device into the Kensington lock hole in the projector.3. Insert the Kensington lock key into the locking mechanism and turn it in the locking direction.You can purchase a locking device from an electronics store or an online shop.Installation and Connection2-18 ...
  • Page 37

    3Using3-1Product Features1. An optical engine adopting new LCD technology1024 x 768 resolution.3P-LCD panel.SP-M206 : Provides a bright, 2000 ANSI lumen screen.SP-M226 : Provides a bright, 2200 ANSI lumen screen.SP-M256 : Provides a bright, 2500 ANSI lumen screen.SP-M275 : Provides a bright, 2700 ANSI lumen screen.SP-M305 : Provides a bright, 3000 ANSI lumen screen.2. Minimized fan noiseMinimizes fan noise through optimized internal air flow and the fan installation structure.3. Multiple input terminalsIncreases the connectivity to peripheral devices such as D-Sub 15P, Video, HDMI(DVI PC signal, supported), etc.4. Audio OutputEquipped with an internal 7W (mono) speaker.5. User adjustmentsAllows adjustment of each input port.Equipped with an internal Test Pattern that can be used to install and adjust the projector.Compact size, lightweight, and portable.6. Convenient Network FunctionThe projector can be monitored and controlled from a PC using the network function.7. Multimedia Functio ...
  • Page 38

    3-2Front, UpperICONNAMEIndicatorsDESCRIPTION- STAND BY (Blue LED)- LAMP (Blue LED)- STATUS (Green/Red/Yellow LED)Refer to the LED Indications.MoveVolume/ Selectbutton/: Use to move or to select an item within a menu.: Use to adjust the volume.MENU buttonUse to display the Menu Screen.SOURCE buttonUse to select the external device signal.POWER buttonUse to turn the projector on or off.Zoom KnobUse to enlarge or reduce image size.Focus RingUse for Focus Adjustment.LensRemote Control Signal ReceiverHole for attaching lens cap stringUsing3-2 ...
  • Page 39

    3-3Remote ControlUsing your projector with another remote control device nearby may result in improper functioning due to remote controlcode (frequency) interference.3-3POWER ( ) ButtonUse this button to turn the projector onand off.QUICK ButtonUse to quickly return to the last menuused.P.MODE ButtonUse to select Picture Mode.AUTO ButtonAutomatically adjust the screen. (Onlyenabled in <PC> mode.)P.SIZE ButtonUse to adjust the size of picturescreen.BLANK ButtonUse to turn off the screen and soundtemporarily.The video and audio will come backon when any button other than the[POWER] button is pressed.Rewind ButtonRewind video in <Media Play> mode.Fast forward buttonFast forward video in <Media Play>mode.Play buttonPlay video in <Media Play> mode.Stop buttonStop video in <Media Play> mode.KEYSTONE buttonCorrect a tilted image.DOCU. ZOOM buttonEnlarge or reduce a document in the<Document> menu under <MediaPlay> mode.Pause buttonPause video in <Media Play> mode.MUTE ( ) ButtonPress to mute t ...
  • Page 40

    Make sure to place your remote control on a table or desk.- If you step on the remote control, you may fall and hurt yourself or damage the remote.You can use the remote control up to a distance of about 32.8 feet (10 m) from the product.Installing Batteries in the Remote Control1. Lift the cover at the back of the remote control upward as shown in the figure.2. Insert two AAA size batteries.3. Close the cover.Using3-3 ...
  • Page 41

    3-4LED IndicationsLED Indications:Light is OnSTATUS:Light is BlinkingLAMP:Light is OffSTAND BYSTATUSIf you press the [POWER] button on the remote control or projector, the screenappears within 30 seconds.The projector is operating normally.The projector is preparing an operation after the [POWER] button on the projector or the remote control has been pressed.The [POWER] button has been pressed to turn off the projector, and the cooling system is in operation to cool off the inside of the projector. (Operates forabout 3 seconds.)The cooling fan inside the projector is not operating normally. Refer to Action 1in Clearing Indicator Problems below.The lamp cover protecting the lamp unit is not closed properly. Refer to Action 2in Clearing Indicator Problems below.The projector has changed to Cooling mode because its internal temperaturehas increased beyond the maintenance limit.Refer to Action 3 in Clearing Indicator Problems below.The projector has turned itself off automatically because ...
  • Page 42

    Clearing Indicator ProblemsCLASSIFICATIONAction 1Action 2STATEMEASURESThe cooling fan system is notoperating normally.If the symptom remains even after disconnecting and then reconnectingthe power cord and turning the projector on again, contact your productprovider or our service center.The lamp cover protecting thelamp unit is not properly closedor the sensor system is notoperating normally.Check if the screws on the side of the projector are securely tightened. Ifthey are and the indicators are still lit, contact your product distributor orour service center.The projector has changed tothe Cooling mode because theinternal temperature of the projector has increased beyondthe maintenance limit.If the internal temperature of the projector has increased beyond the maintenance limit, the projector changes to the Cooling mode before turning offautomatically.Action 3In Cooling mode, the fan speed is increased and the projectors lamp ischanged to <ECO> mode.Check whether the ventilation hol ...
  • Page 43

    3-5Using the Screen Adjustment Menu (OSD: On Screen Display)The Screen Adjustment Menu (OSD: On Screen Display) StructureTo access the Menu, press the Menu button on the product or on the remote. To move in the menu, press the arrow buttons.Menu selections with an arrow on the far right have sub-menus. Press the right arrow button to access the sub-menu. Directionsfor navigating and selecting items in a menu are at the bottom of each menu screen.MENUSUB-MENUInputSource ListEdit NamePictureModeSizePositionDigital NROverscanFilm ModePCZoomInstallLamp ModeAuto KeystoneV-KeystoneBackgroundTest PatternVideo TypeCaptionNetworkResetLanguageMenu OptionSoundFilter CheckTimeAuto Power OnSleep TimerMelodySecurityPanel LockInformationSetupOptionBlack Level3-5-1. InputMENUSource ListDESCRIPTIONYou can select a device connected to the projector to display.Edit Name<PC>-<AV>-<HDMI> - <Media Play>You can edit the names of devices connected to the projector.<VCR>-<DVD>-<Cable STB>-<Satellite STB>-<PVR ...
  • Page 44

    MENUModeDESCRIPTIONSelect a screen mode to match the environment, the kind of images you are projecting, or select acustomized mode you have created based on your requirements.<Mode><Dynamic> : Selects the picture for increased definition in a bright room.<Standard> : Selects the picture for the optimum display in a normal environment.<Presentation> : This mode is suitable for presentations.<Text> : This mode is suitable for text work.<Movie> : This mode is suitable for viewing a movie.<Game> : This picture mode is optimized for playing games.In <Game> mode, the text in still pictures will appear unnatural.<User> : This is a customized mode you create using the <Mode><Save> function.The <Presentation> and <Text> modes are only enabled when the input signal is PC Timing(DSub/HDMI) or <Media Play>.<Contrast> : Used to adjust the contrast between the object and the background.<Brightness> : Used to adjust the brightness of the entire picture.<Sharpness> : Used to adjust the sharpness of t ...
  • Page 45

    MENUPositionDESCRIPTIONUsing this function, you can adjust the screen position if it is not aligned.To adjust, select the direction you want to move the screen, and then press the arrow button pointingin that direction repeatedly.This function does not work in <Media Play> mode.Digital NRIf dotted lines appear in an image or the screen shakes, enabling Digital NR (Noise Reduction) canimprove the quality of the picture.When the input signal is a PC Timing (D-Sub/HDMI) signal, <Digital NR> does not operate.Black LevelIf the black level is unsuitable for the input signal, the dark parts of an image may look unclear or dim.Using this function, you can select a black level that can improve the visibility of the dark parts.The <Black level> can only be set for the [AV], 480i and 576i in AV Timing (D-Sub), and RGBsignals in the [HDMI] input.For [AV], and the 480i and 576i signals of AV Timing (D-Sub).<0 IRE> : Sets the black level to <0 IRE>.<7.5 IRE> : Sets the black level to <7.5 IRE>.For t ...
  • Page 46

    3-5-3. SetupMENUDESCRIPTIONInstallTo tailor the picture to the installation location, (for example, behind a semi-transparent screen, hanging from the ceiling), you can invert the projected images vertically / horizontally.Lamp ModeAuto Keystone<Front-Floor> : Normal Image<Front-Ceiling> : Horizontal/Vertical Reversed Image<Rear-Floor> : Horizontally Reversed Image<Rear-Ceiling> : Vertically Reversed ImageUsing this function, you can set the image brightness by adjusting the amount of light generated bythe lamp.<Eco> : This mode is optimized for screens smaller than 100 inches.This mode decreases the lamp brightness and power consumption in order to extend the lamplifetime and reduce noise and power consumption.<Bright> : This mode maximizes the lamp brightness when the ambient illumination is bright. Asthe brightness of the lamp increases, the lamp lifetime may be reduced and the noise and powerconsumption may increase.If video scenes are distorted or tilted, you can compensate for th ...
  • Page 47

    MENUDESCRIPTIONVideo TypeIf the screen quality is abnormal as a result of the projector not identifying the input signal type automatically in <PC> or <HDMI> mode, Video Type lets you manually set the input signal.This function does not work in <Media Play> mode.In <PC> mode, the menu is only enabled for AV Timing (D-Sub) input signals. For separate H/Vsync, it is only enabled for a 1280 x 720p 59.94Hz/60Hz signal.In <HDMI> mode, <Video Type> is only enabled for the 640x480p 59.94Hz/60 Hz and 1280x720p59.94Hz/60 Hz signals.<Auto>-<RGB(PC)>-<RGB(AV)>-<YPbPr(AV)><Auto>-<PC>-<AV>Usagezoom~GGGyniGGGGwjGGGkTzGGkllyniOh}P~GGGyniGGGGh}GGOz{iSGk}kSGPGGGkTzGGlkk~GGGwwGGGwwOh}P Gh}GGOz{iSGk}kSGPGGGkTzGGlkk~GGGwjGGGoktpGGkkl~GGGh}GGOz{iSGk}kSGPGGGoktpGGlkkTTTh}h3-5PC menuyniOwjPwjCaptionColor,Sharpness,TinthGThe <Caption> function is supported when the external analog signal from the Video input containssubtitles.<Caption> : <Off>-<On><Mode> : <Caption>-<Text><Channel> : <1>-<2><Field> : <1>-<2>A ...
  • Page 48

    MENUDESCRIPTIONNetworkBy connecting a LAN cable between the PC and projector, you can use the following supplementaryfunctions on your PC.On your PC, you can check the projector's condition (lifespan of the lamp, operation error,temperature) and remotely control the projector's power On/Off, brightness, and sound On/Off .<Network> : <On> - <Off><IP Setting><Automatic> : Automatically allots the IP address, Subnet mask and Gateway.<Manual> : Allows you to manually enter the IP address, Subnet mask and Gateway manually.After pressing the [move using the /] button to enter values, change the values using the / buttons andbuttons. Once the values are filled in, press the[ ] button.<Server IP Setting> : Allows you to enter the server PC's IP address.ResetTo use the network function, <Network> must be set to <On>.If the network connection fails, enter the IP address of the server PC under <Server IPSetting>.Using this function, you can reset various settings to the factory default settings.< ...
  • Page 49

    MENULanguageMenu OptionDESCRIPTIONUsing this function, you can select the language used for the menu screen.<Position> : You can move Menu Position up/down/left/right.<Transparency> : You can set the translucency of the menu.<High>-<Medium>-<Low>-<Opaque><Display Time> : You can set the display time of the menu.SoundThe projector comes with an internal 7W (mono) speaker. Use the settings below to tailor the sound asdesired.Filter Check Time<5 sec>-<10 sec>-<30 sec>-<60 sec>-<90 sec>-<120 sec>-<Stay On><100Hz>-<300Hz>-<1kHz>-<3kHz>-<10kHz>Sets the check period for the filter. (Unit: hours)<Off>-<100>-<200>-<400>-<800>If the filter usage time is larger than the filter check period, the filter check message isdisplayed for 1 minute whenever the projector is turned on.Filter check message: "<Check the filter, and if necessary, clean or replace it.>".Auto Power OnWith Auto Power On, if power is supplied to the projector, it turns on automatically without your pressing the Power button.Sleep ...
  • Page 50

    3-6Network Management3-6-1. Management using the Web BrowserThe Web Browser lets you monitor and control one projector from a PC without installing any software. Before youcan use the Web Browser, you must connect your projector to your local area network. For directions explaining howto connect to a network, see section 2-17, Connecting to a Network.To control multiple projectors from a single PC, install and run Samsung Projector Manager.For information about Samsung Projector Manager, go to 3-6-2.Check the network connection between the PC and projector before connecting the Web Browser. If the networkconnection has failed, the Web browser window may not be available for use.To use the Web Browser, your PC must meet the following minimum system requirement :RAM: More than 10MBHard Disk capacity: More than 10MBDisplay resolution: More than 640 x 480Supported OS : Microsoft Windows XP, Windows VistaWeb browser : Microsoft Internet Explorer 6 or later version, Netscape Navigator 9 or l ...
  • Page 51

    3-6-2. Projector Management using PC SoftwareYou can monitor and control more than one projector using Samsung Projector Manager.When installing or using Samsung Projector Manager in PC, you must log in as Administrator.If you log in using your personal login, that login must have full administrator privileges.To use Samsung Projector Manager, your PC must meet the following minimum system requirement :RAM: More than 10MBHard Disk capacity: More than 10MBDisplay resolution: More than 640 x 480Supported OS : Microsoft Windows XP, Windows Vista1. Installing the Samsung Projector ManagerClick 'Samsung Projector Manager' on the CD supplied.Install according to the instructions displayed on the PC screen.2. Running the Samsung Projector ManagerWhen the installation of Samsung Projector Manager and the network setup for the projector have been completed, theSamsung Projector Manager will be available for use.3.Click Start > Samsung Projector > Samsung Projector ManagerThe <Samsung Projector ...
  • Page 52

    <Projector List>, and then select <Add Projector>.UsingSpecify the <Projector Name>, <IP Address> and <Group Name> to register, and then press <ADD>.Any group whose name is not specified will automatically be named <Default Group>. To remove and / orrename a registered projector, right-click and then select <Delete> and / or <Rename> respectively.If a projector is not displayed on the <Projector List > after registration, check if the network connection andthe network settings are properly configured. See section 2-17, Connecting to a Network and section 3-5-3,<Setup><Network> for information and instructions.To save or load the registered projector's information, select <File><Export Config>.3-6 ...
  • Page 53

    Projector ManagementYou can check a projector's lamp condition, temperature, operation, errors, etc in real time.: You can view a projector's Name, IP Address, Group, Power On/Off status, LAMP lifespan, operation errors(represented by icons), etc. in real time.Samsung Projector Manager displays icons that indicate a projector's status. The icons are listed in the tablesbelow. If the icons indicate a problem with your projector, see "Clearing Indicator Problems" in secton 3-4, LEDIndications.Warning and Error status iconsICONSSTATUSSTATEACTIONErrorThe lamp cover protecting the lamp unit is notproperly closed.Refer to Action 2 in Clearing IndicatorProblems.ErrorThe lamp is not operating normally.Refer to Action 5 in Clearing IndicatorProblems.ErrorThe lamp has reached the end of its life.The lamp needs to be replaced.ErrorThe cooling fan 1 is not operating normally.ErrorThe cooling fan 2 is not operating normally.ErrorThe cooling fan 3 is not operating normally.Refer to Action 1 in Clear ...
  • Page 54

    ICONSSTATUSSTATEACTIONWarningThe air filter has reached the end of its life.The air filter needs to be replaced.WarningThe air filter has been blocked by dust.The air filter needs to be cleaned.ErrorThe air filter has been blocked by dust.The air filter needs to be cleaned.Temperature Level Status IconsICONSSTATUSSTATEACTIONTemperature statusThe projector's internal temperature isnormal.(standby mode)None. It's normal.Temperature statusThe projector's internal temperature isnormal.(low)None. It's normal.Temperature statusThe projector's internal temperature isnormal.(medium)None. It's normal.Temperature statusThe projector's internal temperature isnormal.(little bit high)None. It's normal.Temperature statusThe projector's internal temperature ishigher than the limit.Refer to Action 3 in Clearing Indicator Problems.Temperature statusThe projector's internal temperature is toohigh. The projector is turned off automatically.Refer to Action 4 in Clearing Indicator Problems.Managing the Pro ...
  • Page 55

    (Switch Source): Selects a source from HDMI, S-VIDEO, AV, PC, MP.(Blank Off/Blank On): Turns the screen of the projector on or off.(Mute Off/Mute On): Mutes the sound of a projector on/ off.(Adjust Aspect Ratio): Adjusts the aspect ratio of the projector to either 16:9 or 4:3.If the connected source does not have the <Media Play> feature, <MP> is not available in the Source list.If the projector does not have an [S-VIDEO IN] terminal, the <S-VIDEO> source is unusable.: Connecting the Web browser from Samsung Projector ManagerBy connecting to the Web Browser in Samsung Projector Manager, you can use more diverse functions. To performthe Web browser connection, select a Projector to connect to, and then right-click to select <WebControl>.3-6If the Web browser connection fails, check whether the network connection (see section 2-17, Connecting toa Network) and network settings (see 3-5-3, Setup > Network) are correctly configured.Operating one projector using both Samsung Projector Manage ...
  • Page 56

    Using the <Schedule> FunctionUsing the <Schedule> function, you can manage your projectors more efficiently.If you select <List><Schedule>, the following window appears.The screen has four buttons:<New> : Adds a projector to make a Schedule for.<Delete> : Deletes the Schedule for a selected projector.<Delete All> : Deletes the Schedule for all of the projectors.<Edit> : Edits the Schedule for a selected projector.Registering a New ScheduleTo register a new schedule, follow these steps:1. Press the <New> button. The New Schedule screen appears.2. Select the projectors to apply the new schedule to from the <Select Projectors> field. When you select a projector, acheck mark appears in the check box to its left.3. Set the <new schedule>, <Title>, <Repeat>, <Time>, and <Work>, and enter a <Description> of the Schedule.Explanations for each of these terms is below.- <Title> : Sets the name of a Schedule.- <Repeat> : Sets the schedule repetition (<Once> - Executes only once, <Every> - Specifi ...
  • Page 57

    3-6If you want to operate a Schedule loaded by <Import Config>, load the projector's information in advance.Other settingsThe <Tools> selection in the Menu Bar contains two menu items, <Configure Monitoring Items> and <Options>.- <Configure Monitoring Items><Configure monitor items> lets you select an item to be displayed in the monitoring window display. After you selectthe item, you set the display priority of the item by moving it up or down in the list of items you have selected fordisplay.- <Options><Automatically Run> When a PC is turned on, Samsung Projector Manager will be turned on automatically.<Minimize to system tray> Samsung Projector Manager will be minimized to the system tray.<File> contains two selections.- <File> <Export Config> : Saves all of the configured settings under Samsung Projector Manager in the desired filenames to the corresponding folders.- <File> <Import Config> : Imports a saved Configuration file. Sets the Samsung Projector Manager to the savedsettin ...
  • Page 58

    4Media Play Function4-1Connecting a USB Storage Device and Precautions4-1-1. Connecting a USB Device1. Connect your USB storage device to the USB port on the back of the projector.- The main page of the <Media Play> menu appears.The main page of <Media Play> can also be opened by pressing the [MENU] button and selecting <Input><SourceList><Media Play>Supported file systems: FAT, FAT32 (NTFS is not supported.)Multi Partition is not supported.This projector is not compatible with a multi-card reader or USB hub.[Selecting a Device]2. Move to the kind of media you want to view using the / buttons, press the [] button.3. Move to <Internal Memory> or <USB> using the / buttons, and then press the [] button.[Selecting a File]4. Move to the file or folder you want to view or open using the / buttons, and then press the [] button.For Document, Music, and Movie folders, a number appears next to each folder, indicating the number of document,music, or movie files in the folder. For Photo folders, ...
  • Page 59

    Some products which do not comply with standard USB specifications might not operate normally.A USB storage device with automatic recognition application or its own driver might not operate normally.A USB storage device that uses only a designated driver might not be recognized.Recognition speed for USB storage device may vary by device.Do not turn off the product or pull a connected USB storage device out while a USB storage device is in use. Doing so mayresult in damage to the USB storage device or stored file.Use a USB storage device which contains normal files. Abnormal files can cause a malfunction or the files may not play.USB storage devices must be formatted with the FAT or FAT32 (recommended) file systems supported by Windows.<Media Play> may not work normally if the USB storage device is formatted with another file system.If the USB storage device uses external power, please connect the USB storage device to its external power source.Use the USB cable provided with the USB de ...
  • Page 60

    4-2DocumentsYou can view document files in various formats saved on a USB memory device or in the projector's internal memory.Menu displayed from the Documents screenThe Documents screen.The Menu below appears when you press the [MEDIA.P] button while displaying the Documents screen.If you are displaying a screen or item, and then press the [MEDIA.P] button, the menu corresponding to the selecteditem appears.Depending on the current language setting, folder names, file names, or text in a document may appear corrupted.If that is the case, press the [MENU] button and change the language setting in <Language> under <Option>.MENU ITEMDESCRIPTIONViewView a document.CopyIf an external memory device (USB memory device) is connected, files on the external memorydevice can be copied to the projector's internal memory and vice versa.Copy All FilesDeleteDelete All FilesCopy all files to internal and external memory.Delete the selected file.Delete all files in a folder.Menu displayed when you are ...
  • Page 61

    MENU ITEMZoomDESCRIPTIONEnlarge or reduce a document.<Zoom In> : Enlarge a document (25% increments within the range of 100% ~ 500%).<Zoom Out> : Reduce a document.<Custom> : Enlarge or reduce the screen by a specific percentage.<100932573/ - <200932573/ - <300932573/ - <400932573/ - <500932573/Enlarge or reduce a document view using thePage NavigationRotateEnter a page number using the / and / buttons, check the page number in the previewwindow on the upper right corner of the screen, and then select <Go> to move to that page.Display the zoom area.Aspect Ratiobutton on the remote control.Go directly to a specific page.Page Mapor<Off> - <On>If a page is zoomed in, the enlarged area is displayed in the <Page Map> window on theupper right corner.If a page is not zoomed in, the <Page Map> window does not appear.<Fit to Screen> : Display a document to fit the screen size.<Original Fit> : Display a document at its original size.<Fit to Width> : Display a document to fit the screen width.<Fi ...
  • Page 62

    For example, too much data on one sheet in a Excel file.This product supports only one font. If a screen uses other fonts, the image Media Play displays may be different than the originalscreen.(Ex)1. The position of line breaks in a sentence might be dissimilar.2. The position of page breaks in a MS Word document might be changed.- In this case, the document might be shown incompletely according to the Layout properties for <Picture> or<Shapes> or <Object> in MS word . (Please refer to the manual of MS Word for more information on the Layoutproperties.)This product does not support some functions found in original files. For example, the animation function in a PowerPoint file.This product does not support encrypted files (DRM).Media Play Function4-2 ...
  • Page 63

    4-3PhotoEnjoy a slideshow of photos saved on a USB memory device or in the projector's internal memory.Menu displayed from the Photo Thumbnails screenThe Photo Thumbnails screen.The Menu below appears when you press the [MEDIA.P] while displaying the Photo Thumbnails screen.If you are displaying a screen or item, and then press the [MEDIA.P] button, the menu corresponding to that screen oritem appears.Depending on the current language setting, folder or file names may appear corrupted.If this occurs, press the [MENU] button and change the language setting in <Language> under <Option>.MENU ITEMStart SlideshowPlay ModeCopyCopy All FilesDeleteDelete All FilesDESCRIPTIONStart a slideshow.<All Photos>: Play photos in order of file name.<Photo in Folder>: Play photos in a specific folder in order of file name.<Shuffle All Photos>: Play photos found in a specific memory device randomly.<Shuffle Photo in Folder>: Play photos in a specific folder randomly.<Repeat One Photo>: Play only one speci ...
  • Page 64

    SlideshowSelect the file you want using the / buttons on the projector or remote control.Using the remote control during a slideshow:MEDIA.P : Open the photo menu./: View the previous or next photo.: Pause or resume a slideshow.: Return to the previous stage.: Only enabled in the document and movie menu.If you press the [MEDIA.P] button when viewing a slideshow, the following menu appears.MENU ITEMStop Slideshow / StartSlideshowSlideshow SettingDESCRIPTIONStop or start a slideshow.<Transition> : Selects the slideshow mode.<No Effect> - <Wipe> - <Blind> - <Box In/Out> - <Silk> - <Circle> - <Plus> - <Random><Speed> : Adjusts the slideshow playback rate.<Fast> - <Normal> - <Slow><Mode> : Selects manual (view one by one) or auto (slideshow) play.<Auto> - <Manual>If you selected <Manual>, move between photos using the </> buttons on the projector orthe / buttons on the remote control.Play ModeRotate<All photos> : Plays all available image files.<Photo in Folder> : Plays all image files in a ...
  • Page 65

    MENU ITEMBackground MusicSet as Custom LogoDESCRIPTION<On> : Play music defined as background music in file name order.<Off> : Stop the background music that is being played.<Music Setting> : Define background music for a slideshow.Sets the selected image as the projector logo.4-3To use this option, press [MENU] and go to <setup>. Check that <Background> is set to<Custom Logo>.The recommended resolution for a picture to be set as the user logo is 600x300.Media Play Function ...
  • Page 66

    4-4MusicEnjoy music files saved on a USB memory device or the projector's internal memory.Menu displayed from the Music List screen.The Music List screen.The Menu below appears when you press the [MEDIA.P] button while displaying the Music List screen.If you are displaying a screen or item, and then press the [MEDIA.P] button, the menu corresponding to that screen oritem appears.Depending on the current language setting, folder or file names may appear corrupted.If this occurs, press the [MENU] button and change the language setting in <Language> under <Option>.MENU ITEMDESCRIPTIONPlay MusicPlays music files.Play Mode<All musics> : Play music in file name order.<Music in Folder> : Play music in a specific folder in file name order.<Shuffle all musics> : Play music in a specific memory device randomly.CopyCopy All FilesDeleteDelete All Files<Shuffle music in Folder> : Play music in a specific folder randomly.<Repeat one music> : Play only one specific music file repeatedly.If an externa ...
  • Page 67

    Depending on the current language setting, the music file information [] may appear corrupted. If that is the case,press the [MENU] button and change the language in <Language> under <Option>.MENU ITEMPlay Mode4-4DESCRIPTION<All music> : Plays all available music files.<Music in Folder> : Plays all music files in a selected folder.<Shuffle all music> : Randomly plays all available music files.<Shuffle music in Folder> : Randomly plays all music files in a selected folder.<Repeat one music> : Plays a selected music file repeatedly.Media Play Function ...
  • Page 68

    4-5MovieEnjoy video files saved on a USB memory device or in the projector's internal memory.Menu displayed from the Movie List screenThe Movie File screen.The Menu below appears when you press the [MEDIA.P] button while displaying the Movie List screen.If you are displaying a screen or item, and then press the [MEDIA.P] button, the menu corresponding to that screen oritem appears.Depending on the current language setting, folder or file names may appear corrupted..If this occurs, press the [MENU] button and change the language setting in <Language> under <Option>.MENU ITEMDESCRIPTIONPlay MoviePlays video files.Play Mode<All Movies> : Play video files in order of file name.<Movie in Folder> : Play video files in a specific folder in order of file name.<Shuffle All Movies> : Play video files in a specific memory device randomly.<Shuffle Movie in Folder> : Play video files in a specific folder randomly.<Repeat One movie> : Play only one specific video file repeatedly.CopyCopy All FilesDe ...
  • Page 69

    Using the remote control while playing videoMEDIA.P :Open the video menu/: Play the previous or next video file: Pause or resume playing video: Return to the previous stage: View information about the available buttonsIf you press the [MEDIA.P] button when playing a movie, the following menu appears.MENU ITEMPlay ModeSubtitle SettingDESCRIPTION<All Movies> : Plays all available video files.<Movie in Folder> : Plays all video files in a selected folder.<Shuffle all movies> : Randomly plays all available video files.<Shuffle movie in Folder> : Randomly plays all video files in a selected folder.<Repeat one movie> : Plays a selected video file repeatedly.<Subtitle Setting>: Switch the subtitle function <On> or <Off><Language> : Select the subtitle language.<Background> : Change the subtitle background settings.<Position> : Change the subtitle location settings.<On> - <Off><Down> - <Up> - <Reset>The video must have external subtitles in order to view them with the Caption featureturned on. ...
  • Page 70

    4-6SettingsUse the //buttons to move to and access the Setting menus listed below.Media Play Function4-6 ...
  • Page 71

    MENU ITEMOptionsDESCRIPTION<Button Sound> : Change the button control sound settings for the <Media Play> menu.<Off> - <On><Internal Memory Copy> : Change the size of photos you want to copy to internal memory.<Original Size> : Copy photos at the original size to internal memory.<Resized> : Reduce the size of photos according to the optimal screen resolution and then copy.<Open Source License> : To send inquiries and requests for questions regarding open sources, contact Samsung via Email (vdswmanager@samsung.com).Preference<Home Background> : Select the image that will be displayed on the main page of the <Media Play>.<Default> : Display the default image provided by the projector.<Custom> : Display the image you selected as background image.<DivX(R)VOD> : You can view the certified registration code for the projector when you use the VOD(Video on Demand) service provided by DivX.DivXVODABOUT DIVX VIDEO:DivX is a digital video format created by DivX, Inc. This is an official DivX Cert ...
  • Page 72

    4-6-1. Firmware UpdateDownload the latest firmware version from the Samsung Electronics website (http://www.samsung.com) and install.As data saved in the internal memory can be deleted during an update, always back up your data.Do not remove the external memory (USB) device during the update.Do not operate any buttons during the update.Do not turn the projector off during the update.Once the update is complete, turn the projector off, remove the external memory (USB) device and turn the projector on again.Select <Settings><Update/Reset><Product Information> and see if the software version has been updatedsuccessfully.Before Software Upgrade!1. Prepare a USB memory device.2. Download the latest firmware version from the Samsung Electronics website onto your PC.3. Connect the USB memory device to the PC.4. Copy the downloaded software to the USB memory device.To upgrade software1. Connect the USB memory device to the projector.2. Open the main page of <Media Play>.3. Move to <Settings> u ...
  • Page 73

    4-7Supported File FormatsSupported File FormatsITEMDocumentFILE EXTENSIONMS Word 97 ~ 2007 ( doc, docx )Adobe PDF 1.2 ~1.7 ( pdf )MS PowerPoint 97 ~ 2007 ( ppt, pptx )MS Excel 95 ~2007 ( xls, xlsx )Text ( txt)PhotoMusicJPEGThe Progressive format is not supported.CYMK color is not supported (It is displayed Black and white)Crop function is not supported (resolution larger than1024x768)MP3 (sample rate: 8~320Khz)WMA (sample rate: 8~384Khz)ITEMMovieFILE EXTENSIONCODECREMARKS(MAXIMUMRESOLUTION/BITRATE ETC.)AUDIO CODECAVIDivx 3.11Resolution: 720 X 480Supported FormatASF(WMV)Divx 4.xFrame/sec: 30MP3Mbps: 2AC3MP4(MPEG, MPG)Divx 5.1ADPCMDivx 6.0(MULAW,ALAW)XviDAACMPEG-4 SPHE_AAC(AAC+)MPEG-4 ASPWMAWindows Media Video 9Audio sampling rate :MPEG1Resolution: 720 X 480Frame/sec: 30Mbps: 880001102512000160002205024000320004410048000Supported Subtitile formats4-7Media Play Function ...
  • Page 74

    NAMEFILE EXTENSIONFORMATSAMI.smiHTMLSubRip.srtstring-basedSubViewer.substring-basedMicro DVD.sub or .txtstring-basedMedia Play Function4-7 ...
  • Page 75

    5Troubleshooting5-1Before Requesting ServicePlease check the following before requesting After-Sales service. If the problem continues, please contact your nearestSamsung Electronics Service Center.SymptomsInstallation andConnectionMenu andRemoteControlTroubleshootingNo Power.Check the power cable connections.I want to install my projector on the ceiling.The ceiling installation bracket is sold separately. Contact yourlocal product distributor.External Source can not be selected.Be sure that the video cable or cables are properly connectedto the correct jack or jacks on both ends. If the device is notconnected properly, it can not be selected.Remote control does not work.Be sure that the proper external source is selected.Check the battery in the remote. If there is something wrongwith it, replace it with a new battery of the recommended size.Be sure to aim the remote at sensor on the back of the unit andat a distance of no more than approximately 32.8 feet(10 m).Remove any obstacles b ...
  • Page 76

    SymptomsScreen andExternalSourceCannot see picture images.TroubleshootingBe sure that the power cord of the projector is connected.Be sure that the proper input source is selected.Check that the connectors are properly connected to the portsat the back of the projector.Check the Remote Control batteries.Be sure that the <Color> and<Brightness> settings are not attheir lower limit.Poor color.Adjust the <Tint> and <Contrast>.Images are not clear.Adjust the focus.Check if the projector is too far from or too near to the screen.Strange noise.If a strange sound continues, contact your Service Center.An operating LED is lit.Refer to the LED Indications section.Lines appear on screen.On-screen noise may occur when using your PC. Adjust thefrequency (refresh rate) of the screen.No external device screen is displayed.Check the operating status for the external device and checkwhether the adjustable menu items, such as <Brightness> and<Contrast> have been changed correctly in the <Mode> command ...
  • Page 77

    SymptomsNetworkTroubleshootingThe Web browser will not start up.Check the system requirements for the PC to connect to the Webbrowser.The Web browser will not connect to theprojector.1. Check whether the power cable is connected to the projector(See Section 2-9, Connecting the Power).2. Check if the network environments for the PC and projector arecorrect (See Section 2-17, Connecting to a Network).3. Check whether the correct network card in the PC has beenselected when the PC (server) has more than two network cards.Installation of Samsung Projector Manager hasfailed.Check Samsung Projector Manager's system requirements forPCs.The projector will not connect to Samsung Projector Manager.1. Check if the <IP Setting> and network connection betweenthe PC and projector are correct.2. If <IP Setting> for the projector is set to <Automatic>, checkwhether the PC and projector share the same network. If it isnot the same network, configure the IP of the server PC usingthe <Server IP Setting> ...
  • Page 78

    SymptomsMedia PlayFunctionI hear no sound when playing a video file frommy USB storage device.TroubleshootingCheck the audio format of the video file.Sound is not available for non-supported formats such as AC3,etc.Convert the audio format into a supported format using a videoconverter.The subtitle is not displayed for video that isbeing played.Press the [MEDIA.P] button on the screen where video isbeing played and check if <Subtitle Setting> is set to <On>.To view video with the subtitle function on, the video file mustcontain an external subtitle file.For the subtitle file formats supported, please refer to the "4-7Supported File Formats" section.The subtitle file must be located in the same folder as the videofile.The <Media Play> function doesn't work.Reset the <Media Play> mode by pressing the [MENU] buttonand selecting <Setup><Reset><Media Play><RecoveryMode>.If the problem persists, download the latest version of firmwareonto your USB device, connect the USB device to the projec ...
  • Page 79

    6More Information6-1Specifications6-1-1. SP-M206 / SP-M226 / SP-M256MODELPanelSize0.63 inches 3P LCDResolutionXGA (1024 x 768)Aspect ratioPowerLampSP-M206SP-M2264:3Power Consumption240 W240 W260 W(Standby : under 1W)(Standby : under 1W)(Standby : under 1W)180 W200 WVoltage100~240V AC, 50/60HzPower Consumption180 WLife Time3,000 Hours ( Eco : 5,000 Hours )Dimension279 x 229 x 79 mm / 10.98 x 9.02 x 3.11 inchesWeight2.74 Kg / 6.04 lbsKey FeaturesInput signalBrightness2,000 ANSIContrast2000 : 1 (Only in Dynamic of picture mode)Projection Range1 m ~ 14 m / 39.37 inches ~ 551.18 inchesKeystoneAuto: Vertical (20) / Manual : Vertical (20)NetworkWired LAN Port (RJ45), 10 MbpsZoom AdjustmentManualFocus AdjustmentManualScreen Size (Diagonal)Diagonal 30 inches ~ 400 inchesLensF = 1.7 ~ 1.87, f = 19.2 mm ~ 23 mmZoom Ratio1 : 1.2D-Sub 15pAnalog RGB, analog YPbPrHDMIDigital RGB, digital YPbPrRCA x 1Composite videoMedia PlayUSB supportsSpeakerUser EnvironmentSP-M2562,200 ANSI2,500 ANSI7 W (Mono)Tempe ...
  • Page 80

    6-1-2. SP-M275 / SP-M305MODELPanelSize0.63 inches 3P LCDResolutionXGA (1024 x 768)Aspect ratioPowerLampSP-M275SP-M3054:3Power Consumption290 W (Standby : under 1W)Voltage100~240V AC, 50/60HzPower Consumption220 WLife Time3,000 Hours ( Eco : 5,000 Hours )Dimension279 x 229 x 79 mm / 10.98 x 9.02 x 3.11 inchesWeight2.74 Kg / 6.04 lbsKey FeaturesInput signalBrightness2,700 ANSIContrast2000 : 1 (Only in Dynamic of picture mode)Projection Range1 m ~ 14 m / 39.37 inches ~ 551.18 inchesKeystoneAuto : Vertical (20) / Manual : Vertical (20)NetworkWired LAN Port (RJ45), 10 MbpsZoom AdjustmentManualFocus AdjustmentManualScreen Size (Diagonal)Diagonal 30 inches ~ 400 inchesLensF = 1.7 ~ 1.87, f = 19.2 mm ~ 23 mmZoom Ratio1 : 1.2D-Sub 15pAnalog RGB, analog YPbPrHDMIDigital RGB, digital YPbPrRCA x 1Composite videoMedia PlayUSB supportsSpeakerUser Environment3,000 ANSI7 W (Mono)Temperature and HumidityOperating : Temperature 41 F ~ 95 F (5 C ~ 35 C),Humidity : 20 % ~ 80 % (Non-condensing)Storage : Te ...
  • Page 81

    6-2RS232C Command TableCommunication Format (Complies with the RS232C Standard)Baud rate : 9,600 bpsparity : NoneData bits : 8, stop bit : 1Flow Control : NoneSerial Communication Protocol1. Command Packet Structure [7bytes]0x080x22cmd1cmd2cmd3valueA command packet consists of 7 bytes in total.The two bytes 0x08 and 0x22 signify that the packet is for serial communication.The following 4 bytes represent a pre-defined command that can be defined by the user.The last byte is the checksum which checks the validity of the current packet.Header [2 Byte]: Pre-defined values fixed to 0x08 and 0x22.Cmd1 [1 Byte]: The first value of the code defined in the command list (Hexadecimal)Cmd2 [1 Byte]: The second value of the code defined in the command list (Hexadecimal)Cmd3 [1 Byte]: The third value of the code defined in the command list (Hexadecimal)Value [1 Byte]: Input parameter for the command (Default: 0) (Hexadecimal)CS [1 Byte]: Checksum (the 2s complement of the sum of all the values excep ...
  • Page 82

    Command TableCONTROL ITEMGeneralPowerVolumePowerCMD1Display OSD/ Power OnMute0x00CMD30x00Cancel2Direct PowerOff30x010x00(0~100)Up0x010Down0x0200x0000x020x000x00OffOn10x030x000x00OffStillOnInputMore InformationSource List010x040x000x00OffPower OnProtection01OnBlankVALUEOKDirectContinuous0x00CMD201(0~9) Keypad0x050x000x00(0~9)AVAV0x0A0x000x010PCPC0x030HDMIHDMI0x040Media PlayMedia Play0x0506-2 ...
  • Page 83

    CONTROL ITEMPictureMode0x0BCMD20X00CMD30x00VALUE0Standard1Presentation2Text3Movie4Game5User6Contrast0~1000X020x00(0~100)Brightness0~1000X030x00(0~100)Sharpness0~1000X040x00(0~100)Color0~1000X050x00(0~100)Tint (G/R)G50 / R500x060x00(0~100)Color ToneCool20x0A0x001WB6-2DynamicCMD1Cool12Warm13Warm24R offset0x0B0x00(0~100)G offset0x01(0~100)B offset0x02(0~100)R gain0x03(0~100)G gain0x04(0~100)B gain0x05(0~100)More Information ...
  • Page 84

    CONTROL ITEMPictureGamma-3~3SaveDisplay OSDCMD10x0BDigital NRCMD30x0C0x00(0~6)0x0D0x0001Cancel2Direct Save3Normal0x0E0x0000x0F0x000Zoom11Zoom2216:93Off0x100x00OnBlack Level0 IRE/NORMAL0x110x00Off0x120x00Off0x130x00UP0x140x0000x150x000DOWNfineUp10x160x00DOWNResetZoomx1Display OSD010x170x000OK1Cancel2Direct Reset30x180x000x21x42x83LEFTMore Information01Auto adjustmentCoarse01AutoPC01OnFilm Mode017.5 IRE/LOWOverscanVALUEOKResetSizeCMD20x190x000RIGHT1Up2Down36-2 ...
  • Page 85

    CONTROL ITEMPictureSetupHorizontalPositionContinuousVertical PositionContinuousInstallFront-FloorLamp ModeCMD1LEFT0x0BCMD20x1ACMD30x00RIGHTBackgroundTest PatternVideo TypeResetDOWN0x1B0x00Up010x0C0x000x000Front-Ceiling1Rear-Floor2Rear-Ceiling3ECO0x010x0002V-Keystone-50~50Auto KeystoneOff0x020x00(0~100)0x020OnLogo10x030x000Blue1Black2Custom Logo3Crosshatch0x040x000Screen size1Pattern Off2Auto0x050x000RGB(PC)1RGB(AV)2YPbPr(AV)3PC4AV5FactoryDefaultReset FilterTime6-201BrightKeystoneVALUEDisplay OSD0x060x000Ok1Cancel2Direct Factory Default3Display OSD0x010Ok1Cancel2Direct ResetFilter Time3More Information ...
  • Page 86

    CONTROL ITEMSetupResetRecoveryModeSystemResetCaptionCaptionCMD1Display OSD0x0CCMD20x06CMD30x021Cancel2Direct Factory Default3Display OSD0x031Cancel2Direct ResetFilter Time3Off0x070x00Caption0x01Network10x020x03Automatic0x0E0x010x00Subnet MaskGatewayServer IPSettingMore InformationServer IP010x020x00ManualIP Address01OnIP Setting011Off012Network012Field0OkTextChannel0OkOnModeVALUE010x030x040x050x060x000~2550x010~2550x020~2550x030~2550x000~2550x010~2550x020~2550x030~2550x000~2550x010~2550x020~2550x030~2550x000~2550x010~2550x020~2550x030~2556-2 ...
  • Page 87

    CONTROL ITEMOptionLanguageMenu OptionEnglish0x0DCMD20x00CMD30x00VALUE0Deutsch1Nederlands2Espaol3Franais4Italiano5Svenska6Portugus78910Trke1112PositionTransparencyDisplay Time6-2CMD1LEFT0x010x000RIGHT1UP2DOWN3High0x020x000Medium1Low2Opaque35 sec0x030x00010 sec130 sec260 sec390 sec4120 sec5Stay On6More Information ...
  • Page 88

    CONTROL ITEMOptionSound100HzCMD1Up0x0DCMD20x04CMD30x01Down300HzUp0x02Up0x03Up0x04OffUp0x0510x050x00200240038004Sleep TimerOff0x060x00On010x070x00010 min120 min230 min3InformationOff0x080x0000x0A0x000OnMore Information01OffMelody0100Auto PowerONPanel Lock01DownFilter CheckTime01Down10KHz01Down3KHz01Down1KHzVALUEOff10x0B0x000Low1Medium2High36-2 ...
  • Page 89

    6-3Contact SAMSUNG WORLDWIDEIf you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.NORTH AMERICAU.S.A1-800-SAMSUNG (726-7864)http://www.samsung.comCANADA1-800-SAMSUNG (726-7864)http://www.samsung.comMEXICO01-800-SAMSUNG (726-7864)http://www.samsung.comLATIN AMERICAARGENTINA0800-333-3733http://www.samsung.comBRAZIL0800-124-421http://www.samsung.com4004-0000CHILE800-SAMSUNG (726-7864)http://www.samsung.comCOLOMBIA01-8000112112http://www.samsung.comCOSTA RICA0-800-507-7267http://www.samsung.comECUADOR1-800-10-7267http://www.samsung.comEL SALVADOR800-6225http://www.samsung.comGUATEMALA1-800-299-0013http://www.samsung.comHONDURAS800-7919267http://www.samsung.comJAMAICA1-800-234-7267http://www.samsung.comNICARAGUA00-1800-5077267http://www.samsung.comPANAMA800-7267http://www.samsung.comPERU0-800-777-08http://www.samsung.comPUERTO RICO1-800-682-3180http://www.samsung.comREP. DOMINICA1-800-751-2676http://www.samsung.comTRINIDAD & TOBA ...
  • Page 90

    EUROPECZECH800 - SAMSUNG (800-726786)http://www.samsung.comDENMARK70 70 19 70http://www.samsung.comEIRE0818 717100http://www.samsung.comESTONIA800-7267http://www.samsung.comFINLAND030 - 6227 515http://www.samsung.comFRANCE01 48 63 00 00http://www.samsung.comGERMANY01805 - SAMSUNG (726-7864, 0,14/Min)http://www.samsung.comHUNGARY06-80-SAMSUNG (726-7864)http://www.samsung.comITALIA800-SAMSUNG (726-7864)http://www.samsung.comKOSOVO+381 0113216899-LATVIA8000-7267http://www.samsung.comLITHUANIA8-800-77777http://www.samsung.comLUXEMBURG261 03 710http://www.samsung.comMACEDONIA023 207 777-MONTENEGRO020 405 888-NETHERLANDS0900 - SAMSUNG (0900-7267864) (0,10/Min)http://www.samsung.comNORWAY815-56 480http://www.samsung.comPOLAND0 801 1SAMSUNG (172678)http://www.samsung.com022 - 607 - 93 - 33PORTUGAL80820 - SAMSUNG (726-7864)http://www.samsung.comRUMANIA1. 08010 SAMSUNG (72678) doar dinre�eaua Romtelecom, tarif local;http://www.samsung.com2. 021.206.01.10 din orice re�ea, tarifnormalSERBIA0700 ...
  • Page 91

    CISKAZAKHSTAN8-10-800-500-55-500 (GSM: 7799)http://www.samsung.comKYRGYZSTAN00-800-500-55-500http://www.samsung.comMOLDOVA00-800-500-55-500-RUSSIA8-800-555-55-55http://www.samsung.comTADJIKISTAN8-10-800-500-55-500http://www.samsung.comUKRAINE0-800-502-000http://www.samsung.com/uahttp://www.samsung.com/ua_ruUZBEKISTAN8-10-800-500-55-500http://www.samsung.comASIA PACIFICAUSTRALIA1300 362 603http://www.samsung.comNEW ZEALAND0800 SAMSUNG (0800 726 786)http://www.samsung.comCHINA400-810-5858http://www.samsung.com010-6475 1880HONG KONG(852) 3698 - 4698http://www.samsung.com/hkhttp://www.samsung.com/hk_en/INDIA3030 8282http://www.samsung.com1800 1100111800 3000 82821800 266 8282INDONESIA0800-112-8888http://www.samsung.com021-5699-7777JAPAN0120-327-527http://www.samsung.comMALAYSIA1800-88-9999http://www.samsung.comPHILIPPINES1-800-10-SAMSUNG (726-7864)http://www.samsung.com1-800-3-SAMSUNG (726-7864)1-800-8-SAMSUNG (726-7864)02-5805777SINGAPORE1800-SAMSUNG (726-7864)http://www.samsung.comTAIWAN ...
  • Page 92

    MIDDLE EASTTURKEY444 77 11http://www.samsung.comU.A.E800-SAMSUNG (726-7864)http://www.samsung.comAFRICANIGERIA0800 - SAMSUNG (726-7864)http://www.samsung.comSOUTH AFRICA0860-SAMSUNG (726-7864)http://www.samsung.comMore Information6-3 ...
  • Page 93

    6-4Correct Disposal - Europe onlyCorrect Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only(Applicable in the European Union and other European countries with separate collection systems)This marking on the product, accessories or literature indicates that the product and its electronic accessories(e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of theirworking life. To prevent possible harm to the environment or human health from uncontrolled waste disposal,please separate these items from other types of waste and recycle them responsibly to promote the sustainablereuse of material resources.Household users should contact either the retailer where they purchased this product, or their local governmentoffice, for details of where and how they can take these items for environmentally safe recycling.Business users should contact their supplier and check the terms and conditions of the purchase contract. Thisp ...



Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samsung SP-M226 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samsung SP-M226 in the language / languages: English as an attachment in your email.

The manual is 4,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Samsung SP-M226

Samsung SP-M226 User Manual - German - 97 pages

Samsung SP-M226 User Manual - Dutch - 96 pages

Samsung SP-M226 User Manual - French - 96 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info