624004
7
Zoom out
Zoom in
Previous page
1/24
Next page
3
Controls and Functions
INPUT CHANNEL SECTION
The following section details each part of the L1200
and L2000’s INPUT CHANNELS including the LOW
CUT, 3-BAND EQ, the MONITOR and EFX sends, PAN,
GAIN and VOLUME controls.
1 – PEAK LED
The L1200 and L2000’s MIC/LINE pre-amp also
includes a PEAK LED which, when illuminated,
indicates that the input signal is near overload.
2 - GAIN Control Knob
Each of the L1200 and L2000 channel’s pre-amp
stage has a variable GAIN control to help set a clean
level. The Mic/Line inputs’ GAIN control has a range
of -6 to -50dB on the MIC input and +14 to -30dB on
the LINE input. The Stereo inputs GAIN control has a
range of -10 to -50dB on the MIC input and +20 to
-20dB on the LINE input.
3 - LOW CUT Switch
Each of the L Series’ channels include a LOW CUT (or
high pass) filter which rolls off the low frequencies
from 75Hz and below at the rate of 18dB per octave.
Auxiliary Buses ( 4 - 7 )
The L Series include several auxiliary signal paths,
or buses, that can be used to create independent
mixes for sending to the internal or external effects
processors, or to an external monitor system.
These buses start by sending the signal from each
individual channel, which is set with one of the
auxiliary control knobs. Then, the mix of all the
channels auxiliary level is ultimately sent to either
an internal effects processor, or to an output jack to
connect to an external effect or monitor system. To
help you control your effects and monitor mixes, the
L series has four auxiliary buses, with switching to
give you a possibility of 2 monitor mixes with two
effects sends, or 3 monitor mixes and one effects
send.
PRE….? POST….? What’s That?
In order to operate your mixer correctly, it is
important to understand the concept of PRE and
POST fader sends. An auxiliary bus that is set up
as PRE Fader routes, or sends, the signal to its
output from a point in the channels circuit that is
electronically before the channel Fader. That means
the channel Fader has no effect on the PRE aux
level. A Pre Fader send is what you want to use for
a monitor mix, so when the level is changed for the
mix in the main PA speakers using the channel Fader,
the level in the monitor set by the aux control
1
2
3
4
5
6
7
8
10
9
11
12
13
14
15
1 to 24 on the L2000
1 to 16 on the L1200
25/26 to 31/32 on the L2000
17/18 to 23/24 on the L2000
Mono Inputs Stereo Inputs
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samson L1200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samson L1200 in the language / languages: English as an attachment in your email.

The manual is 4,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Samson L1200

Samson L1200 User Manual - German - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info