735223
1
Zoom out
Zoom in
Previous page
1/2
Next page
Icons used in this manual:
Safety
Important info
Contents:
Box Contents
Introduction
Product Compliance and
Safety Information
Installation
User Interface
Status/LED indication
Installers notes
Warranty
Innholdet i esken
Product Compliance & Safety Information
INTRODUCTION
The TRV10RFM is a battery-powered, mini-size thermostatic radiator valve (TRV)
controller using ZigBee wireless communication. Simply replace the existing,
passive head on the standard radiator valve with the TRV10RFM (referred to from
now on as the unit). Use the unit with the VS10RF or VS20RF series of wireless
thermostats and a Universal Gateway.
VS10RF / VS20RF
Thermostat
(Required)
UG600
(Required)
SALUS Wiring Centre
KL08RF
Checking the compatibility of your heating system
4
Our RA adapter also ts this valve.
Once tted the RA adapter should look like this.
If you can not see any thread on
the valve and it looks like this
picture, you may be able to use the
RA adapter supplied.
TRV10 ts 30x1,5 mm thread.
Installing the Unit
Screw the units nut (nger
tight) to the radiator valve
and check that the LED is
solid red.
Press any button on the
unit to adapt it to the
radiator valve. Once all
adaptation noise and LED
activity has stopped, the
unit is ready to pair with
your wireless thermostat.
The unit is now ready
for pairing to the SALUS
thermostat. You may now
start the pairing process.
4 5 6
Remove the battery door
on the side of the unit.
Insert the batteries,
ensuring correct
orientation.
1 2 3
The LED on the unit ashes
green then ashes red before
changing to solid red. When
it is solid red, place the unit
over the radiator valve using
the mounting ring if needed:
Contents of the box
For the latest PFD Instruction Manual, go to
www.salus-controls.com
TRV10RFM
2 AA Batteries
Adapter
Manual
Box Contents
Product Compliance
This product is CE compliant and meets the following EC Directives: Electro-Magnetic Compatibility
directive 2014/30/EU; 2014/53/EU and 2011/65/EU.
Safety Information
Use in accordance with the regulations. The unit is to be used for the control of room temperature
inside the house.
Installation
This accessory must be tted by a competent person, and installation must comply with the
guidance, standards and regulations applicable to the country or state where the product is
installed. Failure to comply with the relevant standards could lead to prosecution.
RX10RF
(Optional)
System Overview
To achieve the best control from the unit and thermostat, we recommend they are
used with the SALUS system receiver congured to RX1. The system receiver will
turn the boiler on or o when requested by the thermostat. See your boiler receiver
manual for more information about the RX1 conguration.
+
Up to 6 units can be connected to a VS10RF/VS20RF
The unit is modulating, which means it opens or closes partially
or 100% depending on the relationship between the actual room
temperature and the required room temperature measured by
the VS10/20RF.
Checking the compatibility of your heating system
The SALUS TRV10RFM is compatible with the majority of thermostatic radiator valves.
Before tting, please check your valve is suitable for use with the SALUS TRV.
Valve
Remove the TRV head
Note: If all the measurements are as stated on this page then the TRV will t directly
to your valve. Also if your valve is not suitable please consider changing your existing
valves, contact your installer.
Measure the thread diameter
(must measure 30mm)
1
2
mm102030
3
mm102030
40
50
Measure the pin length of the valve
when it is in the open position.
(must measure between 13-16mm)
Preparing to Pair the Unit
1
Press and hold the button on the Universal Gateway for
ve seconds. This puts the Universal Gateway in pairing
mode. See your Universal Gateway manual for more
information.
2
Ensure the wireless thermostat is powered up and
ready for pairing. See your thermostat manual for more
information.
3
If you are using the optional RX10RF wireless boiler receiver congured for
remote boiler switching, ensure this has been powered up and the red LED
has gone from ashing to steady. See your boiler receiver manual for more
information.
Pairing the Unit
Press and hold the pairing button for 10 seconds.
You can pair up to 6 units with one thermostat.
Pair the units room by room.
You have paired the unit to the thermostat when the unit LED goes off.
Once paired, the unit operates in automatic mode and receives room temperatures
from the thermostat.
LED Indication
Pairing Button
Manual open/
status indication
Manual close/
status indication
Using the Unit
Leaving the Network
Once paired to a thermostat, press and hold the
pairing button on the unit for 10 seconds.
The red LED come on together for one second.
Note: After you have deleted the unit from the
wireless network, you must reinstall the TRV see
Installing the unit.
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Salus TRV10RFM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Salus TRV10RFM in the language / languages: English as an attachment in your email.

The manual is 3,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info