735219
2
Zoom out
Zoom in
Previous page
1/2
Next page
LED Indication Installation
App Pairing
Dashboard display
Battery replacement
LED Anzeige Installation
App Verbindung
Dashboard Anzeige
Batterieersatz
Voyant LED Installation
App jumelage
Achage du tableau de bord
Remplacement de la pile
Led-indicatie Installatie
App koppelen
Dashboarddisplay
Batterij vervangen
State LED Alarm Sound
Standby
Red LED ashes every
53 sec
N/A
Test Red LED ashes quickly rapid “Di-Di-Di”
Alarm Red LED ashes quickly rapid
“Di-Di-Di”
Mute
Red LED ashes every
10 sec
N/A
Low Power
Red LED ashed one
time
Di
every 53 sec
Fault
Red LED ashed twice
every 53 sec
“Di-Di” twice for
every 53 sec
Pairing
mode
Green LED ashes 5
times per sec
N/A
Pairing
successful
Green LED solid for
3 sec
N/A
Pairing
unsuccessful
Green LED ashes slowly
(twice per sec) six times
N/A
Disconnect
Red LED turns on, then
Green LED ashed slowly
six times
N/A
Etat LED Bruit d’alarme
Être prêt
Voyant LED rouge clignote
toutes les 53 secondes.
N/A
Test
Voyant LED rouge clignote
rapidement.
rapide “Di-Di-Di”
Alarme
Voyant
LED rouge
clignote rapidement.
rapide “Di-Di-Di”
Muet
Voyant LED rouge clignote
toutes les 10 secondes.
N/A
Pile faible.
Voyant LED rouge clignote
une fois.
“Di” toutes les
53 secondes
Défaut
Voyant LED rouge a
clignoté deux fois toutes
les 53 secondes.
“Di-Di” deux fois
toutes les 53
secondes
Mode
jumelage
Voyant LED rouge clignote
5 fois par seconde.
N/A
Jumelage
réussi
Voyant LED vert xe
pendant 3 secondes.
N/A
Jumelage
échoué
Voyant LED verte clignote
lentement (deux fois par
seconde) six fois
N/A
Déconnecter
Voyant LED rouge
s'allume, puis le voyant
LED verte a clignoté
lentement six fois
N/A
Status LED Alarm Ton
Standby
Rote LED blinkt alle
53 Sek
N/A
Test Rote LED blinkt schnell
Schnelles “Di-
Di-Di”
Alarm Rote LED blinkt schnell
Schnelles “Di-
Di-Di”
Stumm
Rote LED blinkt alle
10 Sek
N/A
Niedrige
Energie
Rote LED blinkt einmal
“Di” alle 53 Sek
Fehler
Rote LED blinkt zweimal
alle 53 Sek
“DI-Di” 2 mal alle
53 Sek.
Verbindungs-
modus
Grübe LED blinkt 5 mal
in der Sek
N/A
Verbindung
erfolgreich
Grüne LED leuchtet
für 3 Sek
N/A
Verbindung
fehlgeschla-
gen
Grüne LED blinke lang-
sam ( 2mal je Sekunde)
sechs mal
N/A
Trennen
Rote LED geht an
dann blinkt Grüne LED
langsam 6 mal
N/A
Status LED Alarmgeluid
Standby
Rood LED-lampje knippert
elke 53 sec
NVT
Test
Rood LED-lampje
knippert snel
snel “Di-Di-Di”
Alarm
Rood LED-lampje
knippert snel
snel “Di-Di-Di”
Mute
Rood LED-lampje knippert
elke 10 sec
NVT
Lage energie
Rood LED-lampje knippert
eenmaal
“Di” elke 53 sec
Fout
Rood LED-lampje knippert
tweemaal elke 53 sec
“Di-Di” tweemaal
elke 53 sec
Koppelmodus
Groen LED-lampje
knippert 5 maal per sec
NVT
Koppelen
gelukt
Groen LED-lampje
brandt
3 sec continu
NVT
Koppelen
mislukt
Groen
LED-lampje
knip-
pert langzaam 6 maal
(tweemaal per sec)
NVT
Ontkoppelen
Rood LED gaat aan,
daarna knippert het
groene LED-lampje
langzaam 6 maal
NVT
1
6
1
2A
2B
3
Replace the battery following the correct polarity.
Remove the double-sided tape and stick the alarm into the
ceiling.
Remove the battery insulating strip to turn on the detector
and rotate the sensor clockwise into the bracket.
Retirez le ruban adhésif double face et collez l’alarme au
plafond.
Retirez la bande isolante de la pile pour allumer le détecteur
et pivoter le capteur dans le sens horaire.
Entfernen Sie das doppelseitige Klebeband und befestigen
Sie den Raummelder an der Decke.
Entfernen Sie den Batterieisolierstreifen, um den
Raummelder zu aktivieren, und drehen Sie den Sensor im
Uhrzeigersinn in die Halterung ein.
Verwijder het dubbelzijdige tape en bevestig de detector aan
het plafond.
Verwijder de batterij-isolatiestrip om de detector in te
schakelen en draai de sensor rechtsom in de houder.
Remplacez la pile en respectant la polarité.
Appuyez et maintenez le bouton de réseau pendant
3 secondes.
Setzen Sie die Batterie gemäß der Polarität richtig ein.
Let bij het vervangen van de batterij op de juiste polariteit.
Houd de netwerkknop 3 seconden ingedrukt.
Rotate the sensor anticlockwise to separate it from the bracket.
Install the bracket using the screws or the provided double-
sided tape.
Press and hold the network button for 3 seconds.
Halten Sie die Netzwerktaste 3 Sekunden lang gedrückt.
Faites pivoter le capteur anti-horaire pour le séparer du
support.
Installez le support à l’aide des vis ou du ruban adhésif
double face fourni.
Drehen Sie den Sensor gegen den Uhrzeigersinn, um ihn von
der Halterung zu trennen.
Montieren Sie die Halterung mit den Schrauben oder dem
mitgelieferten doppelseitigen Klebeband.
Draai de sensor linksom om de sensor uit de houder te halen.
Installeer de houder met behulp van de schroeven of het
bijgeleverde dubbelzijdige tape.
2
4
7
9
3
5
8
No Smoke
Kein Raum
Pas de fumée
Geen rook
Smoke
Rauch
Fumée
Rook
SALUS
Smart Home
Go to the App
Allez sur L’appli
Zur App
Ga naar de Apo
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Salus SD600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Salus SD600 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 5,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info