Manual Salus HTRS 230 (page 2 of 2) (English)

735236

Zoom out

Zoom in

1/2

NSB Mode depends on the NSB wired connection.

0V=NSB OFF

230V=NSB ON

This function will be activated only when the device is running in Auto Mode.

If the thermostat receives a NSB signal then it will switch to - . If the NSB is turned

oﬀ, the unit will function in and . You can manually set the thermostat on NSB

by moving the box on the icon.

4. Button Functions

Mode selection.

Long press to return home without saving.

OK key. Short press to conﬁrm selection.

Long press to save and return home.

Long press to enter Temperature oﬀset Heat/Cool.

Decrease or increase Setpoint Temperature.

In Auto Mode by tapping

the or key you

can view the Setpoint

Temperature.

In Auto Mode by holding

the or key you will

access Manual Override

Mode.

After selecting the

temperature press

and the will appear.

Note: In Auto Mode the change in Manual Override Mode is temporary. This is

indicated by the icon. When used as a stand alone, the change is permanent.

In Sunny/ Moon/ Frost

Mode by tapping the

or key you will access

Manual Override Mode.

In Sunny/ Moon/ Frost

Mode the change will be

permanent.

When Auto Mode is

selected again the

permanent override

will end.

5. Frostschutz

Move the box by tapping

or on the Frost

Mode Indicator The device

will enter in Frost Mode.

In Frost Mode you can

select a temperature

between 5°-17°C.

Press the or key to

set the temperature.

Note: During the set-up, press at any time to return to the previous screen or

long press to return to Home display.

Product Compliance & Safety Information

Product Compliance

SALUS Controls hereby declares that the product complies with the essential

requirements of the following EC Directives: 2014/30/EU, 2014/35/EU and

2011/65/EU. The full text of the EU Declaration of Conformity is available at the

following internet address: www.saluslegal.com.

Safety Information

Use in compliance with safety regulations. The unit is to be used for the control of room

temperature inside the house.

Installation

This accessory must be ﬁtted by a competent person, and installation must comply with

the guidance, standards and regulations applicable to the city, country or state where the

product is installed. Failure to comply with the relevant standards could lead to prosecution.

Note: All electrical installation work should be carried out by

a suitable qualiﬁed electrician or other competent person.

Product Description

Thank you for purchasing the SALUS HTRS230 Thermostat. This thermostat is a

device that lets you customise the heating and cooling of your home as needed.

The HTRS230 device from SALUS Controls is a stylish and accurate digital room

thermostat that is ﬁtted with a large easy to read LCD screen and one touch

buttons. You can now simply adjust your home temperature as desired in order

to create a comfortable home environment.

We hope you enjoy our product.

Contents of the box

Manual Contents:

Box Contents

Introduction

Product Compliance and

Safety Information

Installation

User Interface

Status/LED indication

Installers notes

Warranty

Icons used in this manual:

Safety

Important info

Your beneﬁt

Fixing Screws

1 x Installer Manual

Digital Thermostat

Model: HTRS230

INSTALLER MANUAL

SALUS Controls plc

SALUS House

Dodworth Business Park South,

Whinby Road,

Dodworth, Barnsley S75 3SP, UK.

Sales: T: +44 (0) 1226 323961

E: sales@salus-tech.com

Technical: T: +44 (0) 1226 323961

E: tech@salus-tech.com

www.salus-controls.com

SALUS Controls is a member of the Computime Group

Maintaining a policy of continuous product development SALUS Controls

plc reserve the right to change speciﬁcation, design and materials of

products listed in this brochure without prior notice.

Issue Date: Dec 2015

00086/2

For PDF Installation guide please

go to www.salus-manuals.com

Warranty

SALUS Controls warrants that this product (HTRS230) will be free from any

defect in materials or workmanship, and shall perform in accordance with

its speciﬁcation, for a period of ﬁve years from the date of installation. SALUS

Controls sole liability for breach of this warranty will be (at its option) to repair

or replace the defective product.

Customer Name: ......................................................................................................................................

Customer Address: .................................................................................................................................

.............................................................................................................................................................................

....................................................................................... Post Code: ............................................................

Tel No: ................................................................ Email: .............................................................................

Engineers Company: .............................................................................................................................

Tel No: ................................................................ Email: .............................................................................

Instalation Date: .......................................................................................................................................

Engineers Name: ......................................................................................................................................

Engineers Signature: .............................................................................................................................

8. Setting the Thermostat

Device

Function Values Denition Default

Value

d01 Heating control 0 PWM 0

1 On-Oﬀ: 0.5°C(±0.25°C)

2 On-Oﬀ: 1.0°C(±0.5°C)

d02 Room temp oﬀset -3.0°C to

+3.0°C

Oﬀset room temp measuring

error(in 0.5°C)

0.0°C

d05 Cooling control 1 On-Oﬀ: 0.5°C(±0.25°C) 2

2 On-Oﬀ: 1.0°C(±0.5°C)

d07 Valve protection 0 Disable 1

1 Enable

d08 Frost Setpoint 5.0-17.0°C 5.0°C

d12 Max. heating setpoint 5.0-35.0°C 35.0°C

d13 Min. cooling setpoint 5.0-40.0°C 5.0°C

d18 Heating/Cooling

Mode

0 No connection 0

1 Connection

d19 Cooling Blocked 0 Cooling allowed 0

1 Cooling disabled

11. Factory Reset 14. Technical Speciﬁcation

12. Heating/Cooling Mode

13. Temperature Oﬀset (TemperatureCalibration)

Press the indicated keys

together for 3 seconds.

Long press in order to

enter in Settings Mode.

Press to conﬁrm

Select P47 if you want to

reset to factory settings.

Press to conﬁrm

Note: In order to

quickly reach 47 you

can hold down

key. The display will

fast forward to step 5.

9. Setting the Thermostat

Note: The d20 will help you to reduce the power outlet on

the thermostat.

Setting the hysteresis

You can set the hysteresis by entering in Installer Mode, accessing d01 and after

that selecting the desired value ( PWM / 0.5°C / 1.0°C ).

Heating and Cooling Selection

Manually

The mode will be indicated by the ﬂashing icons

Press or to change the modes.

Auto

The CO terminal needs to be connected.

After that the heating and cooling functions will be done automatically.

In Installer Mode, d19 has to be set on 0.

10. Setting the Thermostat

Cooling blocked

When the thermostat is set on Cooling Disabled (d19-->1) it will block the

cooling function for single rooms until the device will receive the heating

command. During the periods of Cooling Blocked no special indicator will be

displayed on the LCD screen. Cooling mode indicator will also be turned oﬀ.

Protection

When room temperature is over the limit of 36°C, all heating outputs will be

turned oﬀ regardless of the control pattern and delay timers. When room

temperature is under the limit of 4°C, all cooling outputs will be turned oﬀ

regardless of the control pattern and delay timers.

Heating Mode Cooling Mode

Temperature Mode Heating Cooling

Sunny 20.0ºC 20.0ºC

Moon 17.0ºC 26.0ºC

Frost (heat system)

5ºC -

The Temperature Oﬀset can be set at any value between

-3°C and +3°C. Press OK to conﬁrm.

Model: HTRS230

Operating Voltage: 230VAC / 50Hz

Max Switching Current: 0,5A

Max No. Actuators: 5pc

Hysteresis: 0,5C /1C

Size: 85mm / 85mm / 25mm

Humidity: 60ºC, 85% RH

Temp Range: 5ºC - 40ºC

Storage Temp: -25ºC - 60ºC

Safety Class: IP30

Certiﬁcation: CE, ROHS II

HRTS230 Thermostat

Gently remove front housing and make the

wiring connections.

2. Terminal Connection

ACTUATOR

E.G.

HEAT

PUMP

EXTERNAL

CLOCK

230VAC

50Hz

1. Mounting the Thermostat

Note: You can wire the thermostat directly to the

KL04NSB, KL08NSB wiring centre or to an actuator

(purchased separatly).

3. Thermostat Icons

BOX means to select mode.

e.g. means Hi temp is selected

means the Hi temp is not selected.

Sunny: Hi comfortable temperature

Moon: Low comfortable temperature

Indicates AUTO ON or AUTO OFF

Frost Protection Indicator:

Frost protection is active, not available in cooling mode.

Heat Mode indicator: Indicates heating is running

Cood Mode indicator:

The icon is ﬂashing when cooling mode active

Temperature indicator

• Display the room temperature

• Display the set temp

Temporary override indicator: If the set temperature is changed

when in program mode, the hand will appear until the next

programs starting time.

You can change the Modes by tapping or and position the box on

the desired one.

Note: The NSB function will be available only when you also have another device

that can send a NSB signal (HTRP230 thermostat, external clock, NSB switch or

another clock thermostat).

6. Night Setback Function (NSB)

7. Installer Mode

Select P49 if you want to

enter Installer Mode.

Press to conﬁrm.

You have reached the

Installer Mode. Select

your options by using

or and then conﬁrm

by pressing .

Note: This function allows you to

customise your thermostat as you

desire. To select the device level

use to jump to the next one d1

> d2 > d5. On the desired level press

then you can choose your

preferences by using or .

Press the indicated keys

together for

3 seconds.

Note: LCD backlight is activated by pressing any key.

Wall mounting

For wall mounting, mark the correct

possition on the wall and mount the

rear case to the wall.

Install the HTRS230 digital room thermostat at roughly 1.5m above ﬂoor level. It should

be mounted in a location where the thermostat is easily accessible and away from direct

sunlight. You can mount the thermostat directly on the wall or you can install it on top of a

wall-box.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Salus HTRS 230 in the language / languages: English as an attachment in your email.

The manual is 5,09 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Salus HTRS 230

Salus HTRS 230 User Manual - German - 2 pages

Salus HTRS 230 User Manual - Dutch - 2 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Salus HTRS 230 Manual

Product: