628422

SAB Heli Division Head HPS3 - H0430-K Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
B
Swashplate
[H0420-S]
- 1 x Swashplate Assembly.
- 2 x Bearings 30x
37x4mm.
- 6 x Uniballs M3x4
5 H3.
- 1 x Uniball M3x4
5 H18.
- 3 x Socket Head Cap Screws M2x5mm.
- 4 x Socket Head Cap Screws M2x8mm.
- 3 x Swasher
2x
5x0.5mm
Radius Arm
[H0421-S]
- 1 x Center Hub.
- 1 x Socket Head Cap Screws
M3x12mm.
- 1 x Socket Head Cap Screw
Shouldered M4x25mm.
- 1 x Metric Hex Nylon Nut M4.
Center Hub
[H0410-S]
- 2 x Radius Arms.
- 2 x Spacer Arm
3x
5x2.7mm.
- 1 x Spacer Hex.
- 1 x Uniball Radius Arms.
- 2 x Socket Head Cap Screws M3x16mm.
- 2 x Socket Head Cap Screws M2.5x10mm.
- 2 x Flanged Bearings
2.5x
6x2.5mm.
- 4 x Flanged Bearings
3x
7x3mm.
Linkage
[H0417-S]
- 2 x Linkages
M3x50mm.
- 4 x Plastic Ball Links.
Damper Derlin
[H0426-S]
- 3 x H0426-A.
- 3 x H0426-B.
- 3 x H0426-C.
- 3 x Washers
10x
16x1mm.
- 3 x Washers
10x
16x0.2mm.
- 3 x Orings 3050.
Recommendations
- These parts should be used only with models SAB Goblin
- Please follow all the instructions shown in the Goblin main manual. In this manual please read Chapther 2, Important notes
- Use Loctite on all threads.
- Put a small amount of grease inside the hub and the O-Ring.
- Check for axial play of the spindle at least after the first 10 flights and add shims if necessary.
- Firmly tighten the blades before flight.
About HPS
HPS stands for "High Precision System". This head has been
developed in order to increase the usable rotor RPM range without
having to change the rigidity of the dampening system.
The new head is developed specially to limit the teetering effect of
the spindle by means of dampening achieved by a special
technopolymer material.
The maximum teetering amount can be adjusted based on the
amount of play shown in figure "A" of the drawing. The O-ring is
necessary to create a radial and axial preload.
The preload can be kept relatively low, thanks to the mechanical
locking properties of the technopolymer dampeners.
With this solution, finding the correct preload is less complex.
This solution is safer because there is a physical "stop" of the
teetering effect with the technopolymer dampers, also with low
axial preload.
The change of preload will serve exclusively to customize the
response of the model.
Furthermore, the spindle can only move vertically thanks to the
elongated hole shown in section "B" of the drawing.
This solution allows an optimal control of the geometry even when
large amounts of torque are introduced into the system.
The head is very accurate and reliable.
Spare Parts
- 2 x Blade Grip.
- 2 x
Thrust Bearing
10x
18x5.5mm.
- 4 x
Bearing
10x
19x5mm.
- 2 x Washer
10x
16x1mm.
- 2 x Button Head Socket Cap M4x8mm.
Blade Grip
[H0182-S]
- 2 x Blade Grip Arm.
- 2 x Socket Head Cap
Screw M4x10mm.
- 2 x Uniball M3x4 Ø5 H3.5.
Blade Grip Arm
[H0183-S]
Spindle Shaft
[H0412-S]
- 2 x Spindle Shaft.
- 2 x Pin 5mm.
- 4 x Socket Head Cap
Screw M2.5x6mm.
- 2 x Socket Head Cap
Screw M4x10mm
- 2 x Washer Ø6,3 x Ø15 x 1mm
ABOUT HPS3
The new HPS 3 head offers an independent dampening system for
each blade grip, there are three dampening settings:
A = Soft for smooth response.
B = Medium.
C = Firm for direct and precise response.
We recommend starting with the medium setting.
For safety reasons we suggest to not exceed 2300 rpm.
In addition, we recommend using a smaller tail pulley in order to
increase the tail rotor speed to counteract the additional torque
introduced by the 3rd rotor blade. You will find a 24T tail rotor pulley
in the kit for this purpose.
TIPS:
Left Side
Right Side
* To remove the dampeners, you
can use a flathead screwdriver
through the hole as shown.
* Clock-wise, counter clock-wise thread
* By turning the linkages you can adjust
tracking. If tracking is adjusted correctly,
you’ll see the metal part line up around
in the center of the opening.
Detail B
SPARE PARTS
RECOMMENDATIONS
These parts should be used only with models SAB Goblin.
· URUKAY and G770 (recommended blades SAB 3BL730, max 750 mm)
· Goblin 700 (recommended blades SAB 3BL690, max 710 mm)
· Goblin Speed (recommended blades SAB 3BL720-1D, max 720 mm)
- 3 blade rotor heads require a much lower cyclic gain on flybarless systems.
We recommend that you set your gain at least 30% lower than the gain
you normally use on your 2 blade rotor head helicopters.
You can start increasing the gain after you complete your first flight.
Running too high of a gain can induce a violent oscillation that can
potentially cause damage to your helicopter in flight.
- Please follow all the instructions shown in the Goblin main manual.
In this manual please read Chapter 2, Important notes
- Use Loctite on all threads.
- Put a small amount of grease inside the hub and the O-Ring.
- Check the spindle for axial play at least after the first few flights and add
shims as necessary, slight axial preload is optimal.The blade grips must
move freely, but they should not move just under their own weight.
- Firmly tighten the blades before flight.
Page 2
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for SAB Heli Division Head HPS3 - H0430-K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of SAB Heli Division Head HPS3 - H0430-K in the language / languages: English as an attachment in your email.

The manual is 5,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info