Manual Ryobi LSDT1202 (page 7 of 132) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

513654

Zoom out

Zoom in

1/132

English

FR DE ES IT NL PT DK SE FI NO RU PL CZ HU RO LV LT EE HR SI SK GR TR

INSTALLING BITS

See Figure 6 - 7.

 Lock the switch trigger by placing the direction of

rotation selector in the center position.

 Open or close the chuck jaws to a point where the

opening is slightly larger than the bit size you intend to

use. Also, raise the front of the drill slightly to keep the

bit from falling out of the chuck jaws.

 Insert the drill bit.

WARNING

Make sure to insert the drill bit straight into the chuck jaws.

Do not insert the drill bit into the chuck jaws at an angle

then tighten. This could cause the drill bit to be thrown

from the drill, resulting in possible serious personal injury

or damage to the chuck.

 Tighten the chuck jaws on the drill bit.

NOTE: Rotate the chuck body in the direction of the arrow

marked LOCK to close the chuck jaws. Do not use a

wrench to tighten or loosen the chuck jaws.

REMOVING BITS

See Figure 6.

 Lock the switch trigger by placing the direction of

rotation selector in the center position.

 Open the chuck jaws.

NOTE: Rotate the chuck body in the direction of the arrow

marked UNLOCK to open the chuck jaws. Do not use a

wrench to tighten or loosen the chuck jaws.

 Remove the drill bit.

TWO-SPEED GEAR SWITCH (HIGH-LOW)

See Figure 9.

A slide switch is located on top of the drill to select either

low (1) or high (2) speed. When using drill in the low (1)

speed range, speed will decrease and unit will have more

power and torque. When using drill in the high (2) speed

range, speed will increase and unit will have less power

and torque. Use low (1) speed for high power and torque

applications and high (2) speed for fast drilling or driving

applications.

ADJUSTABLE TORQUE CLUTCH

See Figure 8.

When using the drill-driver for various driving applications,

it becomes necessary to increase or decrease the torque

in order to help prevent the possibility of damaging screw

heads, threads, workpiece, and so on. In general, torque

intensity should correspond to the screw diameter. If the

torque is too high or the screws too small, the screws may

be damaged or broken.

The torque is adjusted by rotating the torque adjustment

ring. The torque is greater when the torque adjustment

ring is set on a higher setting. The torque is less when the

torque adjustment ring is set on a lower setting.

The proper setting depends on the type of material and the

size of screw you are using.

ADJUSTING TORQUE

 Identify the 24 torque indicator settings located on the

front of the drill.

 Rotate adjusting ring to the desired setting.

1 - 4 For driving small screws

5 - 8 For driving screws into soft material

9 - 12 For driving screws into soft and hard

materials

13 - 16 For driving screws in hard wood

17 - 20 For driving large screws

21 -

For drilling

DRILLING

 Check the direction of rotation selector for the correct

setting (forward or reverse).

 Secure the material to be drilled in a vise or with

clamps to keep it from turning as the drill bit rotates.

 Hold the drill firmly and place the bit at the point to

be drilled.

 Depress the switch trigger to start the drill.

 Move the drill bit into the workpiece, applying only

enough pressure to keep the bit cutting. Do not force

the drill or apply side pressure to elongate a hole. Let

the tool do the work.

WARNING

Be prepared for binding at bit breakthrough. When these

situations occur, drill has a tendency to grab and kick

opposite to the direction of rotation and could cause loss

of control when breaking through material. If not prepared,

this loss of control can result in possible serious injury.

 When drilling hard, smooth surfaces, use a center

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ryobi LSDT1202 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,24 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ryobi LSDT1202 Manual

Product: