557217

Ryobi BID-1801M Manual

10
Zoom out
Zoom in
Previous page
1/89
Next page
OPERATION
NOISE BUILD-UP
Noise (sound pressure level) in the workplace can exceed
85 dB (A). In this case, sound insulation and hearing
protection measures must be taken by the operator.
MOUNTING AND REMOVING THE BIT (Fig. 1)
MOUNTING
■ Slide the sleeve of the bit holder forward.
■ Insert the bit into the bit holder as far as it will go.
■ Release the sleeve.
■ Confirm that the bit is secured by pulling it forward.
REMOVING
■ Slide the sleeve forward.
■ Pull the bit out.
■ Release the sleeve.
CAUTION
Use a bit that matches the screw or bolt to be
driven.
CAUTION
Do not use a damaged bit.
SWITCH
This tool is started and stopped by squeezing and
releasing the trigger.
The rotation speed is variable from 0 through 2400 min
-1
by controlling the trigger-squeezing force.
CHANGING THE ROTATION DIRECTION (Fig. 2)
■ To change the rotation direction, stop the tool and
push the reversing switch to the opposite side.
■ When the reversing switch is pushed in from the
right side, the bit rotates clockwise when viewed from
the handle end of the tool.
■ When the reversing switch is pushed in from the left
side, the bit rotates counterclockwise.
■ The trigger can be locked by positioning the reversing
switch in the middle.
■ Lock the trigger whenever the tool is not in use.
FASTENING TORQUE
The proper fastening torque differs depending on the kind
and size of the screw and the type of the material to
be fastened.
Note: To avoid the reduction of the fastening torque,
keep the battery properly charged.
The fastening torque is affected by the following
factors:
VOLTAGE
When the battery is almost discharged, the voltage will
drop and the fastening torque will be reduced.
FASTENING TIME
If the fastening time is prolonged, the fastening torque
will be increased.
However, if the fastening torque reaches the maximum,
it will not increase any more.
SCREW AND BOLT
Even though the torque coefficient and class of the
screws or bolts are the same, the fastening torque will
differ according to their diameters. Generally, the larger
the diameter, the higher the fastening torque.
On the other hand, even though the diameter of the bolts
or screws are the same, the fastening torque will
differ according to the torque coefficient, their class and
their length.
BIT
Failure to use the correct size bit causes a reduction in
the fastening torque.
SWITCH
The rotation speed and the fastening torque can be
adjusted by controlling the trigger-squeezing force. The
lower the rotation speed, the lower the fastening torque.
WARNING
A battery short-circuit can cause a large current
flow, overheating, burns and even a breakdown.
■ Do not touch the terminals with any conductive
materials.
■ Avoid storing the battery in a container with other
metal objects such as nails, coins, etc.
■ Do not expose the battery to water or rain.
7
GB
English
F D E I P NL S DK N FIN GR H CZ RUS PL
RO
SLO TR
HR
BID-1801M_20 lgs 19/07/05 11:38 Page 7
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ryobi BID-1801M at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ryobi BID-1801M in the language / languages: All languages as an attachment in your email.

The manual is 1,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info