705911

Russell Hobbs 22250-56 Manual

4
Zoom out
Zoom in
Previous page
1/92
Next page
4
6. Don’t fill past the 1500ml mark. If you do, the contents may force the lid off when you start the motor.
7. Place the lid onto the jug with the tab as shown in figure A.
8. Twist the lid clockwise to lock it (fig. B)
9. Push the cap into the hole in the lid.
10. Don’t run the appliance without fitting the cap.
11. Check that the speed control is set to 0.
12. Put the plug into the power socket.
SPEED CONTROL
1. Turn the speed control to the speed you want (1 = low, 2 = high).
2. Turn the speed control back to 0 to turn the motor off.
3. Generally, large quantities, thick mixes, and a high ratio of solids to liquids suggest longer timings
and slower speeds.
4. Smaller quantities, thinner mixes, and more liquids than solids suggest shorter timings and higher
speeds.
5. Don’t run the motor for more than 1 minute, or it may overheat. After 1 minute, switch off for at least
2 minutes, to let the motor cool.
PULSE
Turning the speed control anti-clockwise to Y will give you a short burst at high speed. In this direction,
the knob is spring-loaded. When you let go, it’ll return to 0.
ADDING INGREDIENTS
To add ingredients while the blender is working, remove the cap, pour the new ingredients through the
hole, then replace the cap.
Check that the added ingredients don’t increase the volume in the jug past the 1500ml mark.
CARE AND MAINTENANCE
1. Switch the appliance off () and unplug it.
2. Wipe the outside of the motor unit with a clean damp cloth.
3. Wash the removable parts in warm soapy water, rinse well, drain, and air dry.
4. Don’t put any part of the appliance in a dishwasher.
BLADE UNIT
You may remove the blade unit for cleaning. This is best done with the jug turned upside down.
1. Grip the jug handle with one hand.
2. Grip the bottom of the blade unit with the other hand.
3. Turn the blade unit clockwise till it comes loose from the jug base.
4. Carefully, pull it up and out of the bottom of the jug.
5. Lift the seal away from the blade unit.
6. Wash the seal and blade unit in warm soapy water, rinse, and air dry.
7. Take great care with the blades – don’t handle them directly, use a nylon washing-up brush.
8. Replace the seal round the blade unit.
9. Replace the blade unit in the jug base.
10. Turn the blade unit anti-clockwise to tighten it.
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Russell Hobbs 22250-56 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Russell Hobbs 22250-56 in the language / languages: All languages as an attachment in your email.

The manual is 1,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info