489789

Russell Hobbs 18511-56 Manual

3
Zoom out
Zoom in
Previous page
1/92
Next page
3
12 Don’t use the appliance for any purpose other than those described in these instructions.
13 Don’t operate the appliance if it’s damaged or malfunctions.
14 If the cable is damaged, it must be replaced by the manufacturer, its service agent, or
someone similarly qualified, in order to avoid hazard.
household use only
R PROCESSING
1 Sit the motor unit on a dry, firm, level surface, near a power socket.
2 Route the cable so it doesn’t overhang, and can’t be tripped over or caught.
3 Lower the jug on to the motor unit, then turn the jug clockwise, to lock it in place.
4 Remove the lid.
5 Put the ingredients into the jug.
6 Replace the lid.
C SWITCH ON
7 Check that the speed control is set to 0.
8 Put the plug into the power socket.
C SPEED CONTROL
9 Turn the speed control to the speed you want (1 = low, 2 = high).
10 Turn the speed control back to 0 to turn the motor off.
11 Generally, large quantities, thick mixes, and a high ratio of solids to liquids suggest longer
timings and slower speeds.
12 Smaller quantities, thinner mixes, and more liquids than solids suggest shorter timings and
higher speeds.
Y PULSE
13 Turning the speed control anti-clockwise to Y will give you a short burst at high speed. In
this direction, the knob is spring-loaded. When you let go, it’ll return to 0.
N USING THE BLENDER
14 Don’t run the motor continuously for more than 1½ minutes, it may overheat. After 1½
minutes switch off for at least 2 minutes, to recover.
15 Lower the jug on to the motor unit, then turn the jug clockwise, to lock it in place.
16 Lift the lid off the jug.
17 You’ll find it’s quite stiff (it has be, to keep the ingredients from escaping when you turn the
motor on).
18 Put the ingredients into the jug.
, Don’t fill past the max mark.
19 Put the lid on the jug, and press it down.
20 Align the pips on the sides of the cap with the slots in the hole in the lid, put the cap into the
hole, and turn it about ¼ of a turn clockwise to lock it.
instructions
diagrams
0 off
1 low
2 high
3 speed control
4 motor unit
Y pulse
5 spindle
6 jug
7 handle
8 support
9 blade
10 mixer
11 creamer
12 tab
13 lid
15 pusher
16 disc
17 slicer
18 coarse grater
19 fine grater
20 underside
21 blade unit
22 seal
23 hole
24 pips
25 cap
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Russell Hobbs 18511-56 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Russell Hobbs 18511-56 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info