483579
5
Zoom out
Zoom in
Previous page
1/5
Next page
54
The power steam and vertical steam functions (E 4) are
also possible if the steam control is set to . The interval
between bursts of steam should be about two seconds.
Important:
Never direct the steam at persons or animals!
E5 Spray function
To dampen stubborn creases, press the spray button.
Additional functions
F1 Anti-Drip system
Prevents water escaping from the soleplate when the
temperature is too low.
F2 Anti-scale system
Your iron contains an anti-scale cartridge to reduce scale
deposits. This considerably prolongs the operational life
of your iron. The anti-scale cartridge is an integral part of
the water tank and need not be replaced.
Do not use descaling agents, as these damage the lining of
the steam chamber and so may impair the steam function.
F3 Automatic electronic 3-position cut-out (depending on
model)
If, although switched on, the appliance is not moved, it
will automatically switch off after the following intervals:
After 30 sec., if the iron is standing on the soleplate or
lying on its side.
After 8 mins., if the iron is standing on its heel.
The LED display starts to flash yellow-green-red in regular
sequence. If the appliance is moved, it will automatically
switch on again and begin to heat up again.
After ironing
• Unplug from the mains, pour away remaining water
and set steam control to . Then allow the appliance to
cool down.
• Store the iron standing on its heel.
• Do not wind the cord round the hot soleplate.
Cleaning and maintenance
When the appliance has cooled down, wipe it down with
a damp cloth or sponge, as required.
Dirt can be removed from the soleplate with a damp
cloth or sponge. Do not use sharp or abrasive cleaning
agents or objects.
Important: If the appliance has been standing unused for
long periods, hold it horizontal and allow it to emit
steam for approx. 1 minute to clean the steam ducts and
remove any residue from the iron.
G
H
F
Problems?
If you have any further problems or queries with our products
please call our Customer Relations team first for expert help and
advice:
HELPLINE:0845 602 1454 – UK, 01 4751947 – Ireland
If you are unable to trace the cause of the fault, contact an
official Rowenta Customer Service Centre. The addresses are
shown in the enclosed service centre address list. Further hints
and tips are obtainable from our homepage: www.rowenta.com.
In line with a policy of continuous product improvement
Rowenta reserves the right to change product specifications
without prior notice.
Problems
The iron is plug-
ged in, but the
soleplate of the
iron remains cold.
The soleplate is
not heating up
properly.
LED „Traffic Light“
display does not
light up.
None or too little
steam is being
emitted.
All 3 colours of
the Traffic Light
display flash
alternately.
The traffic Light
display flashes
red fast.
Brown streaks
come through the
holes in the sole-
plate and stain
the fabric.
The soleplate is
dirty or brown
and can stain the
linen.
The soleplate is
scratched or
damaged.
No mains supply.
The temperature
control is set too
low.
Temperature con-
trol set to "0".
There is insuffi-
cient water in the
water tank.
Anti-Drip is active
(F1).
The automatic cut-
out has activated:
the appliance is
on standby.
The temperature
sensor in the sole-
plate is defective.
You are using che-
mical descaling
agents.
You linen is not
rinsed sufficiently
or you have ironed
a new garment
before washing it.
You are using a too
high temperature.
You are using
starch.
You have placed
your iron flat on a
metallic rest-plate.
You have ironed
over a zip.
Check that the mains plug is
properly inserted or try
plugging the iron into a dif-
ferent socket.
Set the temperature control
to a higher temperature (D).
Turn the temperature control
to the required setting.
Fill the water tank (C).
Wait for the soleplate to reach
the correct temperature.
If moved, the appliance will
switch on again.
Call our Customer Relations
Helpline – see below
Do not add any descaling
agents to the water in the
water tank.
Ensure linen is rinsed
thoroughly to remove any
soap desposits or chemicals
on new garments which may
be sucked up by the iron.
See the temperature table to
correctly set the thermostat.
Clean the soleplate as indi-
cated above. Always spray
starch onto the reverse side
of the fabric to be ironed.
Always set the iron on its
heel.
Try to avoid ironing over zips
which may have rough edges.
Possible cause Solution
I
Innen - DX9200_7 08.04.2003 9:32 Uhr Seite 4
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rowenta DX 9300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rowenta DX 9300 in the language / languages: English as an attachment in your email.

The manual is 0,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info