489960

Rotel RCD12 Manual

8
Zoom out
Zoom in
Previous page
1/12
Next page
8
RCD-12 Stereo Compact Disc Player
Note:
When playing CD-DA, MP3 and WMA discs, the Digital Output
provides a PCM data stream. When a DTS CD is played a DTS data
stream is provided.
OPERATION
The RCD-12 can be operated using its front panel buttons or from
corresponding buttons on the supplied infrared remote control. Specific
instructions for each of these controls are detailed below. Most of the
buttons are duplicated on the front panel and on the IR remote control.
However, there are a few exceptions where the buttons are only available
on one or the other. These exceptions are noted in the instructions.
Infrared Remote Control
3
Before using the IR remote control, it is necessary to install two “UM-4/
AAA” batteries (supplied). Remove the plastic cover on the back of the IR
remote, install the batteries (observing the + and – polarity indications),
and reinstall the cover.
To use the IR remote control, aim it at the IR sensor
3
located on the
front panel of the RCD-12.
Display
5
A lighted Display on the front panel of the RCD-12 provides useful
information about the status of the unit, activation of special features, and
track/time information for the disc being played. Each of these indicators
is described in the detailed operating instructions that follow.
Disc Loader Slot
4
A motor-driven slot loader, located in the center of the RCD-12, accept a
compact disc. Place the compact disc into the slot, label-side up. Make
sure the disc is properly centered before loading. The disc can be ejected
by pressing the eject button as explained below.
Transport Control Buttons
These buttons provide basic control functions for the disc transport
mechanism. Except where noted, all functions are available on the RCD-
12 front panel and the IR remote control.
EJECT Button
6Q
When a disc is inserted into the front panel Disc Slot it is pulled into the
disc transport. To eject the disc press the EJECT button on the front panel
or the remote control. If you accidentally press either of these buttons,
press the button again to re-load the disc.
When the eject button is pressed, the Display will read “EJECT”. Once
the disc is completely ejected, the display will read “NO DISC”. When
a disc is loaded, the Display will indicate the number of tracks on the
disc and the total time of the disc in minutes and seconds.
PLAY Button
7M
After the disc is loaded, press the PLAY button to start playing the disc.
The number of the track being played and the elapsed time will be shown
in the display, along with the PLAY indicator. Normally, the disc will start
playing with the first track. However, you can select a different track using
the TRACK buttons or the DIRECT ACCESS buttons (see below) before
pressing the PLAY button to start playing a different selection.
STOP Button
8F
Press the STOP button once to stop disc play. Press the PLAY button to
resume disc play where it was stopped. If the STOP button is pressed
twice, disc play stops, the display shows STOP and programmed selections
are deleted (see below). When the PLAY button is pressed after pressing
the STOP button twice, the disc begins playing from the first track.
PAUSE Button
9N
This button is used to temporarily suspend play. The disc continues to spin
and play will be resumed from the current position. The PAUSE indicator
will light in the Display. To resume playing the disc, press the PAUSE
button again or press the PLAY button.
TRACK Buttons
0L
These buttons are used to select tracks on the disc. When a disc is playing,
pressing the right TRACK button advances to the beginning of the next
track. Pressing the left TRACK button returns to the beginning of the current
track. Pressing twice quickly in succession returns to the beginning of the
previous track. The new track number appears in the Display.
These buttons are also used to select a track before pressing the PLAY
button or when memorizing tracks for the PROGRAM play mode (see
below). These selections are made by continuously pressing the TRACK
buttons until the desired track is reached.
In PROGRAM mode, the TRACK buttons advance or reverse to the
next track in the memorized selection list.
DIRECT ACCESS Buttons
B
Remote Only
These eleven numeric buttons (labelled 1 through 0 and >10) are used
to directly access a track from the IR remote control instead of stepping
through the tracks using the TRACK buttons.
The first ten tracks on a disc can be selected by pressing the corresponding
button. For example, to play the third track, press the 3 button on the
remote control.
When accessing track numbers greater than 10, press the >10 button
followed by the track number. For example, to select track 12, press the
>10 button followed by the 1 button and then the 2 button.
The number of the selected track will appear in the main numeric area
at the center of the Display.
The DIRECT ACCESS buttons may also be used to memorize tracks in
PROGRAM mode (see below).
SEARCH Button
B
Remote Only
These buttons fast forward or fast reverse through the currently playing
disc. One press of these buttons will fast forward or fast reverse at 2X
normal speed. Press these buttons repeatedly will fast forward or fast
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rotel RCD12 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rotel RCD12 in the language / languages: English as an attachment in your email.

The manual is 2,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info