Manual Romer Trifix (page 2 of 2) (English)

490056

Zoom out

Zoom in

1/2

1. Pull the grey fabric loop

to pull

out both locking arms

until you

hear a clicking sound which indi-

cates they are fully engaged.

2. Take the Top Tether

from the

user guide compartment

and

lay it over the child safety seat.

3. Place the child safety seat facing

in the direction of travel on the

vehicle seat.

4. Grasp the child safety seat with

both hands and slide the two

locking arms

ﬁ rmly into the

insert guides

until the locking

arms engage with a clicking noise

on both sides.

Caution: The locking arms are

only correctly engaged if both

of the ISOFIX indicators

are

completely green.

5. Push the child safety seat with a

substantial amount of force as far

back as it will go.

6. Shake the child safety seat to

make sure it is safely attached

and re-check to the ISOFIX indi-

cators

to make sure that both

of them are completely green

10. Tension the strap of the Top

Tether

until the tension

indicator

turns green and the

Top Tether

is tightly tensioned.

For the protection of all vehicle occupants

In the case of an emergency stop or an accident, persons or objects which are not properly secured in the car can cause injury to other vehicle

occupants. For this reason, please always check that...

• the backrests of the vehicle seats are locked (e.g. that the latch on a folding rear seat bench is engaged).

• all heavy or sharp-edged objects in the vehicle (e.g. on the parcel shelf) are secured.

• all persons in the vehicle have their seatbelts fastened.

• the child safety seat is always secured in the car via the ISOFIX anchoring and the Top Tether, even when there is no child in the seat

For the protection of your child

• The more snugly the harness ﬁ ts over your child‘s body, the safer your child will be.

• Please do not ever leave your child unattended in the child safety seat in the vehicle.

Preparatory work

1. If your vehicle is not equipped with the ISOFIX insert guides as

standard, clip the two insert guides

which are included with the

seat* with the cut-out facing upwards onto the two ISOFIX attach-

ment points

of your vehicle.

TIP: The ISOFIX attachment points are located between the surface

and the backrest of the vehicle seat.

2. Move the head restraint on the vehicle seat to the upper position.

* The insert guides make it easier to install the child safety seat with the aid of the ISO-

FIX attachment points and prevent damage to the seat covering. When not in use, they

should be removed and stored in a safe place. On vehicles with a folding backrest the

insert guides must be removed before the backrest is folded.

Any problems which occur are usually caused by dirt or foreign objects on the insert

guides and on the hooks. Clean off any dirt or foreign objects to remedy this type of

problem.

7. Take the Top Tether

and press

the metal tongue

away from

the strap to lengthen the strap and

pull the Top Tether

by the snap

hook

until it makes a V-shape.

8. Guide the Top Tether

on the

left and right-hand sides past the

headrest.

9. Hook the snap hook

into the

Top Tether anchoring point recom-

mended in your vehicle owner‘s

guide.

13. Pull the shoulder straps

one side and put the two buckle

latches

into the harness

retainer

14. Make sure that the buckle

folded forwards and place your

child in the child safety seat.

15. Put the shoulder straps

over

the shoulders of your child.

Caution: The shoulder straps

must not be twisted or swapped.

Caution: Check that the child

safety seat is correctly attached

11. Press the adjusting button

and at the same time pull both

shoulder straps

forwards.

Caution: Do not pull on the shoul-

der pads

12. Open the harness buckle

(press the red button).

• Use on the rear seat:

Move the front seat forward far enough that you child‘s feet cannot hit the backrest of the front seat (to prevent risk of injury).

• The child safety seat can get hot in direct sunshine. Caution: Children‘s skin is delicate and could be injured as a result. Protect the child

seat against intensive direct sunlight when it is not currently in use.

• Only allow your child to enter and exit the vehicle on the pavement side.

• Make stops during longer journeys to give your child an opportunity to run about and play.

To protect your vehicle

Some vehicle seat coverings made of more delicate materials (e.g. velour, leather, etc.) may develop wear marks when child seats are used.

For optimum protection of your seat covers, we recommend using the BRITAX RÖMER Car Seat Protector, which is available from our range

of accessories.

20. Pull on the adjusting strap

until the harness lies ﬂ at and

is close against your child‘s

body.

Caution: Pull out the adjus-

ting strap to the front.

Caution: The hip straps

must be positioned as low as

possible over your child‘s hips.

19. Guide the two buckle latches

together and engage them before

putting them into the harness

buckle

- this should make a

clicking noise.

A correctly adjusted headrest

ensures optimal protection for your

child in the safety seat:

The headrest

must be adjusted

so that the shoulder straps

are at

the same level as your child’s shoul-

ders or slightly above.

17. Pull the adjusting ring of the head

rest

upwards

18. Move the head rest

to the

correct shoulder strap height and

check that it is properly engaged

by lightly sliding the head rest

downwards.

For the safety of your child, before every journey in the car check that...

• the child safety seat is engaged on both sides with the ISOFIX locking arms

in the ISOFIX attachment points

and that both ISOFIX

indicators

are completely green;

• the child safety seat is securely fastened;

• the Top Tether

is tightly tensioned over the backrest of the car seat and the tension indicator

is green;

• the straps of the child safety seat are close to the body without constricting the child;

• the shoulder straps

are correctly adjusted and the straps are not twisted;

• the shoulder pads

are in the right position on your child‘s body;

• the buckle latches

are engaged in the harness buckle

Caution: If your child attempts to open the grey ISOFIX locking buttons

or the harness buckle

, make sure to stop at the earliest op-

portunity. Check that the child safety seat is correctly attached and make sure that your child is properly secured. Teach your child about the

dangers involved.

Removing the child safety seat with ISOFIX

1. Loosen the Top Tether

2. Unhook the snap hook

from the anchoring point and lay the Top Tether

to the front over the child safety seat

3. Press on the grey ISOFIX unlocking buttons on the left and right-hand side of the seat shell

The ISOFIX locking arms

will release and the two ISOFIX indicators

will change colour to red.

4. Pull the seat forwards and stow the Top Tether

back in the user guide compartment

5. Slide the ISOFIX locking arms

back into the seat shell

A rattling noise is produced when the locking arms are pushed back in.

TIP: The locking arms are protected against damage when they are pushed back into the seat base.

Caution: Remove the child safety seat from the vehicle.The child safety seat must never be transported in the car if it is not properly secured.

INSTALLATION

Take the time to carefully read through these instructions, and always keep them ready to hand in the designated pocket on the child seat.

click!

1 cm

User_guide_TRIFIX_GB.indd 2 17.01.2012 08:47:21

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Romer Trifix in the language / languages: English as an attachment in your email.

The manual is 0,97 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Romer Trifix

Romer Trifix User Manual - German - 2 pages

Romer Trifix User Manual - Dutch - 2 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Romer Trifix Manual

Product: