527427
29
Zoom out
Zoom in
Previous page
1/32
Next page
Assembling the C-30 stand
(1) Side board A
(2) Side board B
(3) Center board C
(4) Center board D
(5) Allen wrench
(6) Knob bolts (2 pcs.)
(7) DP-10 (Accessory pedal)
* refer to C-30 owner‘s manual
1.
Attach one end of center board “C” to side board “A.”
Orient center board “C” so that the hardware is on the inside, and
hook the hardware of center board “C" onto the pins of side board
“A,” and press center board “C” downward.
2.
Attach the other end of center board “C” to side board “B.”
Use your hand to support center
board “C,” and hook the
hardware of center board “C”
onto the pins of side board “B,”
and press center board “C”
downward.
3.
Attach center board “D.”
Orient center board “D” so that
the hardware is on the inside,
and hook the hardware at each
end of center board “D” onto the
pins of side boards “A” and “B”
and press center board “D”
downward.
4.
Using the included Allen wrench, tighten the bolts that are
already installed in the center boards.
First, lightly tighten the bolts at
the four locations, and then
tighten the bolts firmly so that
the stand does not rock or
wobble.
* If you will be replacing the decorative panels, do so before placing the
instrument on the stand. For details on how to replace them, refer to the
instructions included with the decorative panels.
* After you’ve finished assembling the stand, attach the included Allen
wrench to the holder located on the inside of side board “A” to prevent it
from being lost.
Unlock the holder, place the
Allen wrench in position,
and then re-lock the holder.
When you unlock the holder,
push up the parts marked (a)
in the illustration.
5.
Align the main unit with the stand.
Place the main unit on the stand
so that the four feet on the
bottom of the unit fit within the
inside of the stand, and then
firmly tighten the two knob bolts
to fasten the unit onto the stand.
* Be careful not to pinch your hands.
Remove the two knob bolts,
separate the main unit from the
stand, and then loosen the four
bolts of the center boards to
disassemble the stand in the reverse
order of assembly.
* Loosening the bolts until their heads are
visible will allow you to disassemble the
stand. Do not remove the bolts entirely.
If the instrument is to be moved
within the same room, it must be
carefully moved by two people
holding the instrument at the
locations shown in the diagram.
If the instrument is to be moved
out of the room or into a different
room, you must separate the main
unit from the stand and carry
them separately. The portion that
connects the main unit and stand
may be damaged if you attempt to
transport the instrument without
separating the main unit and
stand.
When moving the main unit and stand, carry them in a horizontal
position.
Make sure that another person is on hand to help with the
assembly and setup.
When assembling the stand, be careful not to apply
excessive force to any part. Doing so may deform the
hardware or damage the wooden parts.
When assembling or moving the stand, be careful not to
pinch your hands or drop the unit on your feet.
Should you remove the knob bolts, keep them in a safe
place out of children’s reach, so there is no chance of them
being swallowed accidentally.
Check the included items
((
2
)
(
3
)
(
2
)
(
3
)
(
4
)
(
5
)(
6
)(
7
)
(
1
)(
1
)
Wider
Assembly procedure
A
C
A
C
A
C
A
C
B
A
C
B
A
C
B
D
A
C
B
D
Allen wrench
Caution when disassembling the stand
When moving the instrument
(a)
Knob bolt
Foot
C-30_e.book 29 ページ 2008年3月10日 月曜日 午前10時31分
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roland C-30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roland C-30 in the language / languages: English as an attachment in your email.

The manual is 4,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Roland C-30

Roland C-30 Quick start guide - English - 2 pages

Roland C-30 User Manual - German - 34 pages

Roland C-30 User Manual - Dutch - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info