68388
15
Zoom out
Zoom in
Previous page
1/20
Next page
– 14 – – 15 –
4. ELECTRICAL WIRING
IMPORTANT! Disconnect the positive power terminal ("+12V") or remove the main
fuse near the car battery before you start any wiring work!
The power supply of the car audio system must be disconnected until the entire wiring
installation is completed.
Use rubber grommets when running cables through any metal or sharp plastic panels, to
prevent accidental shorting or shearing. Make sure the cables do not interfere with normal
operation of the vehicle. Especially the music signal cables (RCA interconnects) should be
kept far away from any potential sources of electrical interference i.e. electronic vehicle
management systems (engine computers, relays etc.) fuel pumps, wiring harnesses etc.
4.1 CONNECTION OF POWER CABLES
Run the positive power cable ("+12 V") directly from the positive terminal of the car battery
to the amp-module. Make sure the power cable makes good contact to the battery; i.e. use
an appropriate battery clamp that accepts big gauge power cables! For protection of your
car audio system and your entire car against electrical fire hazards from a shortcircuit of the
main power cable with chassis ground, you must insert a main fuse (holder) within the first
30cm of the battery. The fuse type/value should be matching the limitations of your main
power cable and the requirements of your car audio system. For example 60 A fuse when
using the 20 mm² power cable. Now you route the ground cable to the amp-module. It is
best to keep the ground cable ("-12V") as short as possible, i.e. to find a chassis contact
very close to the amplifier. The ground power cable must have the same cross-section as
the positive power cable. It is recommended to use a corrosion-resistant gold-plated power
ring or a massive ground clamp between the ground cable and the chassis ground point.
Keep in mind that audible interferences and problems originating in the power supply of the
amplifier are mostly based on a bad ground contact.
4.2 RCA INTERCONNECTS / REMOTE LEAD
Carefully run the RCA audio signal interconnect(s) and the remote switching cable from the
head-unit to the amplifier. The audio signal cables should be routed completely separate
from the power cables. Use only double or triple shielded quality cables!
Connect the remote wire lead to the remote output of the headunit and to the remote input
terminal of the amplifier. Finally connect the RCA interconnect cable(s) to the respective
outputs on the head-unit and the RCA inputs of the amp-module.
4.3 HIGH LEVEL INPUT
If your headunit does not have RCA outputs, you can use the "HIGH LEVEL INPUT".
To use this, connect the "HIGH LEVEL INPUT" to the loudspeaker outputs of your headunit
or parallel to the rear speakers in your car.
If your headunit does not support a remote output, you can use the automatic turn on/
off function. This function is controlled by the audio signal itself. Therefore please set the
"SWITCH" to "ON".
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rodek RN110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rodek RN110 in the language / languages: English, German as an attachment in your email.

The manual is 2,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info