167808
28
Zoom out
Zoom in
Previous page
1/32
Next page
4. CROSSOVER SETTINGS
Now you can set an appropriate lowpass crossover fre-
quency. For this purpose, open the input gain control
- the arrow of the knob should point to "noon" - so you
can hear the subwoofer playing. Ideally, the low-pass
cut-off frequency should be set between 50 to 90 Hz - and
this setting has to be entirely determined by ear. Try to
find lowpass crossover frequency setting, that gives you
a "full-bodied" bass reproduction with enough impact in
the upper bass range.
Note: If the lowpass crossover frequency is set too low,
the sound will have a tendency to sound extremely soft
and low-end heavy!
Now you can adjust the subsonic-highpass, if you wish
to squeeze out the most (max-dB) of your subwoofer
system. Turn the highpass frequency control up, to a
point where you can hear that the bass reproduction
starts to get "thinner". The subsonic highpass frequency
should be set to a value between 20 to maximum 50 Hz.
4.2.4 ADJUSTING INPUT SENSITIVITY
To reach a maximum noise-free dynamic headroom
from each individual head unit/amplifier/speaker com-
bination, it is important to set the respective input gain
controls correctly. The input level settings determine the
actual signal-to-noise ratio, and they are also responsible
for obtaining the maximum distortion-free SPL (sound
pressure level) from your specific setup.
4.2.2 BANDPASS FOR KICKBASS
SYSTEMS
If you intend to operate a kickbass loudspeaker system in
the front doors of your vehicle, you must select two cross-
over frequencies at the active crossover of your RODEK
amplifier. The operation mode must be set to bandpass.
The bandpass filter contains a highpass (10 - 400Hz) with
a cascaded lowpass (30 - 400Hz) filter. The lowpass
crossover frequency point is usually set at a frequency
that equals at least twice the value of the highpass
crossover frequency setting. The lowpass filter is mostly
set a little lower, than the highpass crossover frequency
setting of the satellite channels.
Kickbass speaker system, front door mounted,
recommended bandpass frequencies
16 cm Kickbass Speaker System 80 - 110 Hz Highpass
200 - 250 Hz Lowpass
4.2.3 BANDPASS FOR SUBWOOFER
SYSTEMS
To drive a subwoofer system, the integrated electronic
crossover must also operate in bandpass mode. Before
you attempt to adjust the lowpass crossover frequency,
you must first turn the (subsonic)highpass frequency
control counterclockwise to its lowest position at 10 Hz.
28
R1500-4100A2 Manual.indd 28R1500-4100A2 Manual.indd 28 07.07.2004 10:59:12 Uhr07.07.2004 10:59:12 Uhr
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rodek r 4100 a at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rodek r 4100 a in the language / languages: English, German as an attachment in your email.

The manual is 1,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info