66477
5
Zoom out
Zoom in
Previous page
1/72
Next page
5
DESIGN FEATURES
INSTALLATION
INSTALLATION CONSIDERATIONS
The following is a list of tools needed for installation:
Volt/Ohm Meter
Wire strippers
Wire crimpers
Wire cutters
#2 Phillips screwdriver
Battery post wrench
Hand held drill w/assorted bits
1/8" diameter heatshrink tubing
Assorted connectors
Adequate Length—Red Power Wire
Adequate Length—Remote Turn-on Wire
Adequate Length—Black Grounding Wire
8. Infrasonic Filter A 28Hz High Pass filter designed to prevent frequencies below the audio range
from being applied to the subwoofer from the amplifier. Consequently improving subwoofer
performance and power handling, particularly in vented enclosures.
9. Gain Control The input gain control is preset to match the output of most source units. It can be
adjusted to match output levels from a variety of source units.
10. Variable Crossover – Is a built-in adjustable filter selectable for High-Pass (HP),All Pass (AP),or
Low-Pass (LP) operation variable from 40Hz to 400Hz in x1 mode, and 400-4000Hz in x10 mode.
11. Frequency Multiply Switch Used to set the multiplier for the crossover frequencies between x1
and x10.A setting of x1 leaves the adjustable crossover frequency from 40-400Hz.A setting of x10
changes the adjustable crossover frequency to 400-4000Hz
12. Slope Switch Used to select between a 12dB/octave Butterworth or 24dB/octave Linkwitz-Riley
filter.
13. RCA Input Jacks The industry standard RCA jacks provide an easy connection for signal level input.
They are nickel-plated to resist the signal degradation caused by corrosion.
14. RCA Active Pass-Thru Jacks This Active Pass-Thru provides a convenient source for daisy-chaining
an additional amplifier without running an extra set of RCA cables from the front of the vehicle to the
rear amplifier location.
15. 2/4 Channel Switch – Pressing this switch in, switches the inputs to a 2-channel mode, allowing
connection to only the front inputs with a 4-channel output.
16. Preamp Output Crossover – Is used to set the crossover output for the Pass-Thru Jacks
selectable for High-Pass (HP),All Pass (AP), or Low-Pass (LP) operation. If set to HP or LP the
frequency of th Pass-Thru outputs will be the same frequency selected for the main crossover.
17. Remote Terminal This heavy duty, platinum-plated wire connector will accept wire sizes from
12 AWG to 24 AWG.This terminal is used to remotely turn-on and turn-off the amplifier when
+12V DC is applied.
18.
Power Terminals The power and ground connectors on the amplifier are platinum-plated and will
accommodate up to 1/0 AWG wire maximizing the input current capability of the amplifier.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rockford Fosgate T8004 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rockford Fosgate T8004 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 6,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info