Manual Rockford Fosgate Punch P10002 (page 6 of 64) (English, German, French, Italian, Spanish, Spanish)

490252

Zoom out

Zoom in

1/64

INSTALLA

TION

MOUNTING LOCATIONS

Engine Compartment

Never mount this unit in the engine compartment. Mounting the unit in the engine compartment will void

your warranty.

Trunk Mounting

Mounting the amplifier vertically will provide adequate cooling of the amplifier.

Mounting the amplifier on the floor of the trunk will provide the best cooling of the amplifier.

Mounting the amplifier upside down to the rear deck of the trunk will not provide proper cooling and will

severely affect the performance of the amplifier and is strongly not recommended.

Passenger Compartment Mounting

Mounting the amplifier in the passenger compartment will work as long as you provide a sufficient amount

of air for the amplifier to cool itself. If you are going to mount the amplifier under the seat of the vehicle,

you must have at least 1" (2.54cm) of air gap around the amplifier's heatsink.

Mounting the amplifier with less than 1" (2.54cm) of air gap around the amplifier's heatsink in the

passenger compartment will not provide proper cooling and will severely affect the performance of the

amplifier and is strongly not recommended.

BATTERY AND CHARGING

Amplifiers will put an increased load on the vehicle's battery and charging system.We recommend

checking your alternator and battery condition to ensure that the electrical system has enough capacity to

handle the increased load of your stereo system. Stock electrical systems which are in good condition

should be able to handle the extra load of any Punch Series amplifier without problems, although battery

and alternator life can be reduced slightly.To maximize the performance of your amplifier, we suggest the

use of a heavy duty battery and an energy storage capacitor.

WIRING THE SYSTEM

CAUTION:If you do not feel comfortable with wiring your new unit, please see your

local Authorized Rockford Fosgate Dealer for installation.

CAUTION:Before installation, disconnect the battery negative (-) terminal to prevent

damage to the unit, fire and/or possible injury.

CAUTION:Avoid running power wires near the low level input cables, antenna, power

leads, sensitive equipment or harnesses.The power wires carry substantial

current and could induce noise into the audio system.

1. Plan the wire routing. Keep RCA cables close together but isolated from the amplifier's power cables

and any high power auto accessories, especially electric motors.This is done to prevent coupling the

noise from radiated electrical fields into the audio signal.When feeding the wires through the firewall

or any metal barrier, protect them with plastic or rubber grommets to prevent short circuits. Leave

the wires long at this point to adjust for a precise fit at a

later time.

2. Prepare the RED wire (power cable) for attachment to the

amplifier by stripping 5/8" of insulation from the end of the

wire. Insert the bared wire into the B+ terminal and tighten

the set screw to secure the cable in place.

NOTE:The B+ cable MUST be fused 18" or less from the

vehicle's battery. Install the fuseholder under the hood

and ensure connections are water tight.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Rockford Fosgate Punch P10002 in the language / languages: English, German, French, Italian, Spanish, Spanish as an attachment in your email.

The manual is 2,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Rockford Fosgate Punch P10002 Manual

Product: