592133

Roadstar HRA-1300DAB Manual

5
Zoom out
Zoom in
Previous page
1/19
Next page
English English
5 6
longer the bar will be from left to right.
DLS
DLS stands for Dynamic Label Segment which is a scrolling message that the broadcaster
may include in their transmissions. The message usually includes information such as
programme details …etc.
Programme type
This describes the style of the programme that is being broadcast. If the information is
not available, the display will show
“<Program Type>”.
Ensemble/Multiplex (Group name)
The Ensemble/Multiplex is a collection of radio stations that are bundled and transmitted together
in a single frequency. There are national and local multiplexes, local ones contain stations that
are specific to that area.
Note: Press and hold the INFO button for longer than 2 seconds, the software version number
will be displayed.
FM RADIO
1. To select FM, repeatedly press the MODE button until you see “Switch to FM” is displayed,
the display will finally show FM
and the frequency.
2. To activate auto search, turn and hold the SELECT control until it starts to scan the
frequency band, the display will show
“Searching … > .” or “Searching … < .”, and it will stop automatically once a station has been
found.
3. To activate manual tuning, repeatedly turn the SELECT control and when you see your
desired frequency appears in the display, release the control.
4. To select the FM stereo/mono reception mode, press the SELECT button to toggle
between the “Auto” or “Mono” selection.
Note: The radio will automatically switch between the stereo and mono reception, but you can
override this and switch this function manually which is helpful for poor signal reception.
STORING AND RECALLING STORED STATIONS
In either DAB or FM mode, you can store up to 10 stations to the favourite presets; this will
enable you to get direct access to your favourite stations.
1. To store a preset, first tune to your desired station, then press and hold the PRESET
button until the display shows “Save to P#” and flash.
2. Repeatedly turn the SELECT control to select your desired station preset number then
press the SELECT button to confirm your selection, the display will show “Preset # saved”.
3. To recall a preset station, first press the PRESET button once, then repeatedly turn the
SELECT control to scroll up or down
the presets that you have stored. When the display shows your desired preset number, release
the control. If the preset hasn’t been allocated a station, the display will show “Empty preset #”.
ALARM FUNCTION (AC operation only)
This unit incorporates an identical Dual Alarm function in AC operation. You can have
two individual alarm wake-up time and wake-up mode settings to wake you to an
electronic buzzer tone or your favourite radio station (DAB/FM). There is no alarm
function in battery operation.
Setting the alarm time and wake-up mode
1. Press the ALARM button once to enter into the Alarm Menu, then repeatedly turn the
SELECT control followed by pressing on the SELECT button to select Alarm (1 or 2).
2. Again repeatedly turn the SELECT control to select “Alarm Setting”, then press the
SELECT button to confirm, the display will show “Alarm # Setting” and the hour digit of the
alarm time will flash.
3. Repeatedly turn the SELECT control followed by pressing on the SELECT button to
adjust and confirm your desired alarm time first set the hour and then the minute.
4. After the confirmation of the minute setting, the alarm time is set and you will enter into
the wake-up mode settings.
5. Again repeatedly turn the SELECT control followed by pressing on the SELECT button
to adjust and confirm the wake-up mode settings first set the DAB and FM Preset (1-10),
then the Buzzer Tone (1 or 2), finally the alarm Volume level.
6. After the confirmation of the alarm volume level setting, the wake-up mode settings are
all completed and the alarm function
is now ready for you to activate.
7. Repeat the above procedures to set the other Alarm (1 or 2).
Activating the alarm function
1. To activate the alarm function, first press the ALARM button to enter into the Alarm
Menu, then turn the SELECT control followed by pressing on the SELECT button to select
Alarm (1 or 2).
2. When the display shows “Alarm Source”, press the SELECT button to go for the
selection.
3. Repeatedly turn the SELECT control and the associated alarm wake-up mode will be
displayed and changed in the below sequence:
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roadstar HRA-1300DAB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roadstar HRA-1300DAB in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 1,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info