592189

Roadstar CLR-2860CD Manual

3
Zoom out
Zoom in
Previous page
1/20
Next page
MMI of CLR-2860UMP
___________________________________________________________________________________________________________
3
With the supplied mounting plate you can install the appliance under, for example, a wall cupboard . For the
installation of the appliance proceed as follows:
Slide the mounting plate to the rear and remove the mounting plate.
Select a suitable installation location for the appliance ( see also the section Set-up location requirement).
Hold the mounting plate under the installation location. Thereby the front edge of the mounting plate
should be approx. 2.2cm behind the front of the cupboard so that, after the installation, the appliance is
flush with the cupboard.
Mark the 4 securing points with a pencil.
Using a spike or nail, make a small depression at the retaining lug into the respective depression on the
mounting plate.
Firmly screw the mounting plate on with the supplied screws(see illustration)
Place the appliance aslant, with the recesses in the top face of the appliance, in the mounting plate until
the appliance audibly locks into place.
Check to ensure that the appliance is securely seated.
Key List:
1. Power: Power on/Off
2. Open : Control of CD tray
3. UP | FF： Station tune up and forward of CD playback
4. DOWN|RW： Station tune down and backward of CD play back
5. Mode | Stop： Mode set and Stop of CD playback
6. MEM.Scan/AMS | Pause /Play： Preset Station review ,AMS, Play & Pause of CD play back
7. AL1/VOL-： Alarm 1 setup and Volume decrease
8. AL2/VOL+： Alarm 2 setup and Volume increase
9. Preset+ / Repeat： Call back preset station for up
10. Preset-： Call back preset station for down
11. Prog. /MEM： Station Memory
12. FUNC/user： CD、AUX、FM 、selector / user select
13. AOT/Dim： Automatic Off Timer and Dimmer control
14. Timer Opera for timer function
1 Start to Using the device
When unit is powered up first time, Automatic update function will start automatically and “PLEASE WAIT FOR
SETTING THANKS “is flashing on LCD, When press any key to terminate this function.
Note: When unit is powered up first time, Automatic update function will start automatically in 3~5
minutes. If the signal is received, time display on LCD accordingly
When the automatic system setting had been terminate by user, the date and clock are
defaulted to 01.01.2012 ,0:00.
12
7
8
14
1
6
9
10
4
2
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roadstar CLR-2860CD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roadstar CLR-2860CD in the language / languages: English, German as an attachment in your email.

The manual is 0,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info