543945

Revell B-25 SSP Twin Engine Manual

1
Zoom out
Zoom in
Previous page
1/4
Next page
* APPLY STICKERS
*APPLIQUEZ LES AUTO-COLLANTS
* REPEAT SEVERAL TIMES
* A REPETER PLUSIEURS FOIS
* ALTERNATIVE ASSEMBLY
* ENSEMBLAGE ALTERNATIVE
* REMOVE AND THROW AWAY
* A RETIRER ET JETER
* OPTIONAL PARTS
* PIECES EN OPTION
B-25 BOMBER
KIT 0216 85021600200
If you have any questions or comments, call our hotline at: (800) 833-3570
or, please write to:
Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007
Be sure to include the plan number (85021600200), part number, description, your return address and phone number.
Visit our website: www.revell.com
Revell Inc Elk Grove Village, IL. Copyright © 2008. All rights reserved.
The North American B-25 Mitchell
bomber had a wingspan of 67'
7". Fuselage length was 52' 11".
Normally during WWII this version of
the B-25 carried four .50 cal. machine
guns in two revolveing turrets and
one in the nose. The aircraft flown
in the famous Doolittle raid had their
lower turrets replaced by additional
fuel tanks and two "dummy broom-
stick guns" extended from the tail to
discourage attack by enemy aircraft.
The markings on your Revell Doolittle
Raider B-25 bomber represent those
used on the actual plane that Lt. Col.
Doolittle flew himself during the raid.
Your Revell B-25 Mitchell bomber
model includes revolving turrets and
elevating guns, realistic details and
authentic waterslide decal markings.
* Study the assembly drawings.
* Each plastic part is identified by a number.
* In the assembly drawings, some parts will be marked by
a star (★) to indicate chrome
plated plastic.
* For better paint and decal adhesion, wash the plastic
parts in a mild detergent solution. Rinse and let air dry.
* Check the fit of each piece before
cementing in place.
* Use only cement for polystyrene plastic.
* Scrape plating and paint from areas
to be cemented.
* Allow paint to dry thoroughly before
handling parts.
* Any unused parts may be discarded.
DECAL APPLICATION INSTRUCTIONS
1. Cut desired decal from sheet.
2. Dip decal in water for a few seconds.
3. Place wet decal on paper towel.
4. Wait until decal is movable on paper backing.
5. Place decal in position on model, face up and slide
backing away.
6. Press out air bubbles with a soft damp cloth.
7. Milkiness that may appear is for better decal adhesion
and will dry clear. Wipe away any excess adhesive.
8. Do not touch decal until fully dry.
9. Allow the decals 48 hours to dry before applying clear
coat.
NOTE: Decals are compatible with
setting solutions or solvents.
READ THIS BEFORE YOU BEGIN LIRE CE QUI SUIT AVANT DE COMMENCER
* Etudier les schémas de montage.
* Chaque pièce en plastique est identifiée par un numéro.
* Sur les schémas de montage, certaines pièces sont marquées d'une étoile
(★) pour indiquer qu'elles sont en plastique chromé.
* Pour une meilleure prise de la peinture et des autocollants, laver les pièces
en plastique avec une solution détergente peu concentrée. Les rincer et
les laisser sécher à l'air.
* Vérifier que chaque pièce s'ajuste bien avant
de la coller en place.
* N'utiliser que de la colle pour polystyrène.
* Gratter les parties à coller pour enlever le chrome et la peinture.
* Laisser la peinture bien sécher avant de manipuler les pièces.
* Toute pièce inutilisée peut être jetée.
DIRECTIVES D'APPLICATION DES AUTOCOLLANTS
1. Découper l'autocollant désiré de la feuille.
2. Tremper l'autocollant dans de l'eau pendant quelques secondes.
3. Placer l'autocollant mouillé sur une serviette en papier.
4. Attendez que l'autocollant puisse être déplacé sur son support en papier.
5. Mettre l'autocollant en position sur le modèle face sur
le dessus et faire glisser le support pour l'enlever.
6. Appuyer avec un chiffon doux humide pour éliminer les bulles d'air.
7. La substance laiteuse qui peut apparaître est destinée à améliorer
l'adhésion de l'autocollant et devient incolore au séchage. Essuyer pour
enlever tout excédent d'adhésif.
8. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec.
9. Laisser l'autocollant sécher pendant 48 heures avant d'appliquer
une couche transparente.
REMARQUE: Les autocollants sont compatibles avec
les solutions de fixage ou les solvants.
Noir satine
Noir mat
Vert de zinc
Argent
Jaune mat
Rouge
Gris mat
Havane
Chair
Brun mat
This paint guide is provided to
complete this kit as shown on the box
.
Ce guide de peinture est fourni pour reproduire le
modèle réduit qui apparaît sur la boîte.
Semi Gloss Black
Flat Black
Zinc Chromate
Silver
Flat Yellow
Red
Flat Gray
Tan
Flesh
Flat Brown
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Revell B-25 SSP Twin Engine at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Revell B-25 SSP Twin Engine in the language / languages: English, French as an attachment in your email.

The manual is 1,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info