700359
11
Zoom out
Zoom in
Previous page
1/12
Next page
ENG
10 11
TROUBLE SHOOTING
If you are having problems after installation follow the trouble shooting procedures below.
Procedure 1:
Check the device for proper connections.
Verify that POWER LED is on. If POWER LED is on skip to Step 3, if not continue.
1. Check the fuse of the device or the external fuse on battery positive cable. Replace if necessary.
2. Verify that Ground connection is connected to clean metal on the vehicle’s chassis. Repair/replace if necessary.
Please ensure that you have reconnected the GND connection at the battery after the installation.
3. Verify that there are 9 to 16 Volts present at the positive battery and remote turn-on cable. Verify quality connections for both cables at device,
head unit and battery/fuse holder. Repair/replace if necessary. Check that the vehicle charging system is maintaining proper voltage.
Procedure 2:
PROTECTION LED is on.
1. If the PROTECTION LED is on, this is a sign of driving the device at very high power levels without adequate airflow around the device.
Shut off the system and allow device to cool down. If the previous items do not solve the problem, a fault may be in the device.
Check that the vehicle charging system is maintaining proper voltage.
Procedure 3:
Check the device for a proper audio signal.
1. Verify good RCA input connections at head unit and device. Check entire length of cables for kinks, splices, etc.
Test RCA inputs for AC volts with stereo on. Repair/replace if necessary.
2. Use another audio source for testing to provide an audio signal to the Line Input.
Procedure 4:
Check the device for a popping noise while turning on.
1. Disconnect input signal to device and turn device on and off.
2. If the noise is eliminated, connect the REMOTE lead of device to source unit with a delay turn-on module.
OR
1. Use a different 12 Volt source for REMOTE lead of the device (e.g. battery direct just for testing).
2. If the noise is eliminated, use a relay to isolate the device from noisy turn-on output.
3. Don‘t connect REMOTE directly to the battery after testing to avoid a discharge of the battery.
Procedure 5:
Check the device if you experience excess Engine Noise.
1. Route all signal carrying wires (RCA, Speaker cables) away from power and ground wires.
OR
2. Bypass any and all electrical components between the head unit and the device. Connect the head unit
directly to input of the device. If noise goes away the unit being bypassed is the cause of the noise.
OR
3. Use another audio source for testing to provide an audio signal to the Line Input.
OR
4. Remove existing ground wires for all electrical components. Reground wires to different locations.
Verify that grounding location is clean, shiny metal free of paint, rust etc.
OR
5. Add secondary ground cable from negative battery terminal to the chassis metal or engine block of vehicle.
OR
6. Have alternator and battery load tested by your mechanic. Verify good working order of vehicle electrical system including distributor,
spark plugs, spark plug wires, voltage regulator etc.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Renegade RS800A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Renegade RS800A in the language / languages: English, German as an attachment in your email.

The manual is 1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info