Manual REMKO RKL490 DC (page 4 of 20) (English)

587574

Zoom out

Zoom in

1/20

Safety notes

Disposal of equipment and

components

Only recyclable materials are used

in the manufacture of the devices

and components.

Help protect the environment by

ensuring that the devices or com-

ponents (for example batteries) are

not disposed in household waste,

but only in accordance with local

regulations and in an environmen-

tally safe manner, e.g. using certi-

ﬁed ﬁrms and recycling

specialists or at collection

points.

Intended use

Depending on the model, the

equipment and the additional

fittings with which it is equipped

is only intended to be used as an

air-conditioner for the purpose of

cooling or heating the air in an

enclosed room.

Different or additional use shall

not be classed as intended use.

The manufacturer/supplier assumes

no liability for damages arising from

an unintended use of the equip-

ment. The user bears the sole risk in

such cases.

Using the equipment as intended

also includes working in accord-

ance with the operating manual

and installation instructions and

complying with the maintenance

requirements.

Carefully read the operating in-

structions before commissioning the

equipment for service. It provides

useful tips and information as

well as hazard warnings to prevent

injury or material damage . Fail-

ure to follow the directions in this

manual can result in endangerment

to persons, the environment and

the equipment itself and will void

any claims for liability.

■ Keep this manual and the refrig-

erant data sheet near the unit.

■ The unit should be set up and

installed only by qualified per-

sonnel.

■ The set-up, connection, and

operation of the unit and its

components must be in accord-

ance with the operating condi-

tions stipulated in this manual

and comply with all applicable

local regulations.

■ Mobile units must be set up

securely on suitable surfaces and

in an upright position. Station-

ary units must be permanently

installed for operation.

■ Modification of equipment and

components supplied by REM-

KO is not permitted and can

cause malfunctions.

■ Equipment and components

may not be operated in areas

where there is an increased risk

of damage. Observe the mini-

mum clearances.

■ The electrical supply is to be

adapted to the requirements of

the equipment.

■ The operational safety of equip-

ment and components is only

assured if they are fully as-

sembled and used as intended.

Safety devices may not be modi-

fied or bypassed.

■ Do not operate equipment or

components with obvious de-

fects or signs of damage.

■ All housing parts and openings

in the device, e.g. air inlets and

outlets, must be free of foreign

objects, fluids, or gases.

■ The equipment and components

must be kept an adequate dis-

tance from flammable, explo-

sive, combustible, abrasive and

dirty areas or atmospheres.

■ Touching some parts of the

equipment can result in burns or

other injury.

■ Installation, repair and mainte-

nance work may be carried out

only by authorised specialists.

Visual inspections and cleaning

can be performed by the opera-

tor as long as power is discon-

nected from the equipment.

■ To preclude any danger from

the equipment, take appropri-

ate hazard-prevention measures

when performing installation,

repair or maintenance work or

cleaning the equipment.

■ The equipment or components

are not to be exposed to any

mechanical stresses, extreme

levels of humidity or direct

sunlight.

Warranty

Prerequisites for possible warranty

claims are customer or his accept-

ing representative has completely

filled out the "warranty registration

card" supplied with the unit and

was completely filled out and re-

turned to REMKO GmbH & Co. KG

and placing the unit in service.

The warranty conditions are listed

in the "General terms and condi-

tions". Furthermore, only the par-

ties to a contract can strike special

agreements beyond these condi-

tions. For this reason please contact

your contractual partner in the first

instance.

Disposal of packaging

All products are packed for trans-

port in environmentally friendly

materials. Make a valuable con-

tribution to reducing waste and

sustaining raw materials. Only

dispose of packaging at approved

collection points.

Environmental

protection

and recycling

REMKO RKL

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of REMKO RKL490 DC in the language / languages: English as an attachment in your email.

The manual is 1,53 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO RKL490 DC

REMKO RKL490 DC User Manual - German - 16 pages

REMKO RKL490 DC User Manual - Dutch - 20 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

REMKO RKL490 DC Manual

Product: