587557
11
Zoom out
Zoom in
Previous page
1/16
Next page
11
Troubleshooting
This unit has been designed using state-of-the-art manufacturing processes and it has been tested repeatedly to
ensure that it is working properly. However, should problems occur, refer to the following list.
* Unplug the unit from the power supply before performing any work on it! *
Problem Possible cause Check Remedy
The device does not start
or switches itself off auto-
matically.
Power failure. Are all other electrical compo-
nents working?
Check current and wait for the
device to start again.
Defective power fuse /
main switch is off.
Are all currents for lighting
functional?
Replace power fuse /
Switch on main switch.
Power supply line damaged. Are all other electrical compo-
nents working?
Maintenance by authorised
personnel.
Temperature range is either
too high or too low. Is the fan still working? Keep the unit within operating
temperature range 20 to 35 °C.
Water tank is full Is the “Tank Full” signal light lit
up? Empty tank. See page 7.
The surrounding temperature is
outside of the operating range
(16 to 35 °C).
Does “E1“ appear on the dis-
play
Do not operate the unit outside
of the operating range.
The device is either not
cooling at all or only
cooling a little bit.
The exhaust hose is bent, ex-
tended, place downwards or
blocked.
Does the cooling performance
improve when the device is
operated without an exhaust
hose and without a filter?
Make sure that the exhaust
channel is not blocked
Dirty filter
input and/or output opening
blocked by foreign matter
Is the filter dirty? Clean the filter
The unit is too close to the wall
or other objects.
Has the minimum distance of
50 cm been maintained? Maintain minimum distance
Windows and doors open /
thermal load increased
Has something been changed
in the design or application?
Close windows and doors /
reduce thermal load
Low pressure in the setup
room when operating the unit
Does the cooling performance
improve when a door or win-
dow is opened?
Correct pressure in the setup
room
“Cooling” operating mode not
set
Is the FAN operating mode
set? Switch unit operating mode
Device is switched on with the
timer function Is the “TIMING ON“ LED lit up? Press the On / Off button again
Temperature setting too high
Is the temperature setting
higher than the temperature of
the room?
Lower temperature
Excess voltage due to light-
ning.
Was there lightning recently in
the region ?
Unplug device from the power
supply with switch 5 and restart
The unit does not to
respond to the infrared-
remote control.
Remote-controlled batteries
are dead or the transmission
distance is too far
Does the button function work
at a distance of approx. 3 m ?
Replace batteries /
reduced distance or change
location.
Polarity of the batteries is in-
correct after replacement Is the polarity correct? Insert the batteries correctly.
Pay attention to the labels.
Condensation water leaks
out of the device.
The device is not standing up-
right Is the device upright? Place upright and make sure it
is firmly in place
The plug for the condensation
drain is not inserted correctly
or is damaged.
Is water dripping out of the
condensation drain?
Insert the plug correctly or re-
place if necessary.
The air flap is not opened wide
enough
Check the position of the air
flap.
Open the air flap as wide as
possible.
Should the unit still not be working despite these checks, please contact an authorised service centre.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO MKT260 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO MKT260 in the language / languages: English as an attachment in your email.

The manual is 1,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO MKT260

REMKO MKT260 User Manual - German - 16 pages

REMKO MKT260 User Manual - Dutch - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info